Front Drive Shaft
Exploded View

Removal and Installation
REMOVAL
Remove engine under cover. Refer to Removal and Installation
Drain A/T fluid. Refer to Draining.
Remove tires. Refer to ROAD WHEEL TIRE : Removal & Installation.
Remove front wheel sensor from steering knuckle. Refer to Removal and Installation.
Remove brake caliper assembly. Hang brake caliper assembly in a place where it will not interfere with work. Refer to FRONT BRAKE CALIPER ASSEMBLY : Removal & Installation.
Remove disc rotor.
Remove brake hose bracket from steering knuckle.
Using lock nut chisel [SST: KV40108800 (NI-52982)] (A), release stacked area of wheel hub lock nut.


Loosen wheel hub lock nut, using a hub lock nut wrench [SST: KV40104001 (NI-53385)] (A).

Separate upper link from steering knuckle, using the ball joint remover (commercial service tool), and remove upper link.
Set suitable jack under lower link.
Remove steering outer socket. Refer to Removal and Installation.
Remove lower link from steering knuckle.
Remove steering knuckle.
Remove drive shaft from front final drive assembly.

Use the drive shaft attachment [SST: KV40107500 ( − )] (A) and a sliding hammer (commercial service tool) (B) while inserting tip of the drive shaft attachment between housing and front final drive assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
Place the protector [SST: KV38107900 (NI-33904) (NI-52469-1)] (A) onto front final drive assembly to prevent damage to the front final drive assembly side oil seal while inserting drive shaft. Slide drive shaft sliding joint and tap with a hammer to install securely.

Clean the matching surface of wheel hub lock nut and wheel hub and bearing assembly.
Clean the matching surface of drive shaft and wheel hub and bearing assembly. And then apply paste [service parts (440037S000)] to surface
of joint sub-assembly of drive shaft.
Amount paste : 1.0 – 3.0 g (0.04 – 0.10 oz) Insert drive shaft to wheel hub, and then temporarily tighten hub lock nut.

Tighten the wheel hub lock nut to the specified torque.

: 218 - 223 N·m Using lock nut crimp punch [SST: KV40108700 ( − )] (A), stake wheel hub lock nut and drive shaft staked area.


A : 6.2 mm (0.244 in) B : 29.4 - 30.8 mm (1.157 - 1.213 in)
Disassembly and Assembly
DISASSEMBLY
Fix shaft with a vise.
Remove circular clip from housing.
Remove dust shield from housing.
Remove boot bands, and then remove boot from housing.
Put matching marks on housing and shaft.
Remove stopper ring with suitable tool, and pull out housing.

Put matching marks on ball cage/steel ball/inner race assembly and shaft.
Remove snap ring, then remove ball cage/steel ball/inner race assembly from shaft.

Remove boot from shaft.
Perform inspection after disassembly. Refer to Inspection.
ASSEMBLY
Remove old grease on housing with paper waste.
Install boot and boot bands to shaft.
Remove the tape wrapped around the serration on shaft.
Install ball cage/steel ball/inner race assembly
, align it with the matching marks on shaft
put during the removal.

Secure ball cage/steel ball/inner race assembly onto shaft with snap ring
.
Apply the appropriate amount of grease onto housing and sliding surface.
| Grease amount | Drive Shaft |
Install housing to shaft.
Install stopper ring to housing.
After installed, pull shaft to check engagement between housing and stopper ring.
Install boot securely into grooves (indicated by “*” marks) shown in the figure.

To prevent deformation of the boot, adjust the boot installation length (L) to the value shown below by inserting the suitable tool into the inside of boot from the large diameter side of boot and discharging inside air.
| L | Drive Shaft |
Secure the large and small ends of the boot with boot bands using the boot band crimping tool [SST: KV40107300 (NI-51751)] (A).


| M | : 1.0 – 4.0 mm (0.039 – 0.157 in) |
Secure housing and shaft, and then check that they are in the correct position when rotating boot. Install them with boot band when the mounting positions become incorrect.
Install dust shield to housing.
Install circular clip to housing.
DISASSEMBLY
Fix shaft with a vise.
Remove dust shield from joint sub-assembly.
Remove boot bands and then remove boot from joint sub-assembly.
Screw the drive shaft puller (commercial service tool) (A) 30 mm (1.18 in) or more into the thread of joint sub-assembly, and pull joint sub-assembly from shaft.

Remove circular clip from shaft.
Remove boot from shaft.
Perform inspection after disassembly. Refer to Inspection.
ASSEMBLY
While rotating ball cage, clean old grease on joint sub-assembly with paper waste.
Fill serration slot joint sub-assembly
with NISSAN genuine grease
or equivalent until the serration slot and ball groove become full to the brim.

Install boot and boot bands to shaft.
Remove the tape wrapped around the serration on shaft.
Position circular clip on groove at the shaft edge.
Align both center axles of the shaft edge and joint sub-assembly. Then assemble shaft with joint sub-assembly holding circular clip.
Install joint sub-assembly to shaft using plastic hammer.

Pull the joint sub-assembly in the axial direction away from transaxle assembly. Confirm that the joint sub assembly cannot be pulled out.
Apply the specified amount of grease into the boot inside from large diameter side of boot.
| Grease amount | Drive Shaft |
Install the boot securely into grooves (indicated by “*” marks) shown in the figure.

To prevent the deformation of the boot, adjust the boot installation length (L) to the specified value shown below by inserting the suitable tool into inside of the boot from the large diameter side of boot and discharging the inside air.
| L | Drive Shaft |
Install new boot bands securely.
Small boot bandSecure the ends of the boot with boot bands using the boot band crimping tool [SST: KV40107300 (NI-51751)] (A).


M : 1.0 – 4.0 mm (0.039 – 0.157 in)
Set boot band to the drive shaft boot groove and temporarily fix pawl
of boot band to
of boot band.
Pull protrusion of boot band tighten with boot band crimping tool [SST: KV40107310 (-)] (A) in the direction shown by arrows (
).

Secure joint sub-assembly and shaft, and then check that they are in the correct position when rotating boot. Install them with boot band when boot installation positions become incorrect.
Install dust shield to joint sub-assembly.
Inspection
INSPECTION AFTER REMOVAL
Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for significant looseness.
Check boot for cracks, damage, and leakage of grease.

Disassemble drive shaft and exchange malfunctioning part if there is a non-standard condition.
INSPECTION AFTER DISASSEMBLY
Shaft
Check shaft for runout, cracks, or other damage. Replace it if necessary.
Joint Sub-Assembly (Wheel Side)
Check the following items, replace the parts if necessary.
Joint sub-assembly for rough rotation and excessive axial looseness.
The inside of the joint sub-assembly for entry of foreign material.
Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly.
Replace joint sub-assembly if there are any non-standard conditions of components.
Housing (front final drive assembly side)
Replace housing if there is scratching or wear of housing roller contact surface.
INSPECTION AFTER INSTALLATION
Check wheel sensor harness for proper connection. Refer to Exploded View.
Check the wheel alignment. Refer to Inspection.
Adjust neutral position of steering angle sensor. Refer to Work Procedure.