Sonar Sensor (front)
Exploded View
CITY MODELS

| Front bumper fascia | Corner sensor front LH holder | Corner sensor front LH | |||
| Center sensor front LH holder | Center sensor front LH | Center sensor front RH holder | |||
| Center sensor front RH | Corner sensor front RH | Corner sensor front RH holder | |||
| vehicle front | |||||
OFF ROAD MODELS (WITH WELDING TYPE)

| Front bumper fascia | Corner sensor front LH | Center sensor front LH | |||
| Center sensor front RH | Corner sensor front RH | Center sensor front RH finisher | |||
| Center sensor front LH finisher | |||||
| vehicle front | |||||
OFF ROAD MODELS (WITHOUT WELDING TYPE)

| Front bumper fascia | Corner sensor front LH holder | Corner sensor front LH | |||
| Center sensor front LH | Center sensor front RH | Corner sensor front RH | |||
| Corner sensor front RH holder | Center sensor front RH finisher | Center sensor front LH finisher | |||
| :Always replace after every disassembly. | |||||
| vehicle front | |||||
Removal & Installation
REMOVAL
Center sensor
Disconnect sonar sensor harness connector , follow the procedure below.Slide the lock
of the connector toward the direction (1). Keep pushing (2) in the lock of connector and remove the harness connector
to ward the direction (3).

Unhook the pawls
in the direction (
) and remove the sonar sensor
from the sensor holder.

Remove the mounting screws
, and remove the sensor holder
from the front bumper fascia.

Disconnect sonar sensor harness connector, follow the procedure below.Slide the lock
of the connector toward the direction (1). Keep pushing (2) in the lock of connector and remove the harness connector
to ward the direction (3).

Unhook the pawls
in the direction (
) and remove the sonar sensor
from the sensor finisher.

Unhook the pawls
in the direction (
) and remove the sensor holder
from the front bumper fascia.

Corner sensor
Disconnect sonar sensor harness connector , follow the procedure below.Slide the lock
of the connector toward the direction (1). Keep pushing (2) in the lock of connector and remove the harness connector
to ward the direction (3).

Unhook the pawls
in the direction (
) and remove the sonar sensor
from the sensor holder.

Remove the mounting screws
, and remove the sensor holder
from the front bumper fascia.

Disconnect sonar sensor harness connector , follow the procedure below.Slide the lock
of the connector toward the direction (1). Keep pushing (2) in the lock of connector and remove the harness connector
to ward the direction (3).

Unhook the pawls
in the direction (
) and remove the sonar sensor
from the sensor holder.

Remove the sensor holder
from the front bumper fascia. (Without welding type)

INSTALLATION
| : Connector direction | |||||
OFF ROAD MODELS
| : Connector direction | |||||
Center sensor
Install in the reverse order of removal.
Corner sensor
Install in the reverse order of removal.
Install in the reverse order of removal when install only the sensor.
Follow the procedure below when replace the sensor holder.
Hook the pawls
to install the sonar sensor to the sensor holder.
Degrease and clean the inner side of the bumper fascia base line
and then apply primer (3M K500,K520 or equivalent) on the sensor holder installing face
, which is shown as on the figure.
Dry the primer for more than 3 minutes and peel off the double sided tape
releasing paper (film) and then taking precautions not to contact the bumper with the double sided tape ( on the figure), bend the sensor holder
to the arrow direction as shown on the figure
.
Match the sonar sensor part
shown on the figure, to the sensor installing hole of the bumper fascia.
Remove the sensor from the sensor holder and press the adhesion face (part
on figure) throughout with your thumb for more than 2 seconds and pressure bond the sensor holder [Target pressure: 50 N (5.1kg, 11.3 lb)].
Hook the pawls
to install the sonar sensor to the sensor holder.
Shake the part
of the sensor holder shown on the figure up and down and then right and left to confirm that the holder has been installed (bonded) firmly.
Connect connector to the sonar sensor.
Install the front bumper. Refer to Removal and Installation.