Brake System LHD

Brake booster

In this manual: Brake System LHD
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~4min read

Exploded View

2WD

1. Master cylinder assembly

1. Master cylinder assembly 2. Vacuum pipe
3. Brake booster
4. Lock nut
5. Clevis
6. Gasket
7. Spacer

4WD: N·m (kg-m, ft-lb)


4WD

1. Master cylinder assembly

1. Master cylinder assembly 2. Brake booster
3. Lock nut
4. Clevis
5. Gasket
6. Spacer

Removal and installation: N·m (kg-m, ft-lb)


Removal and installation

REMOVAL

1. Perform inspection before removal. Refer to BR-47, "Inspection and Adjustment". 2. Remove cowl top and cowl top extension. Refer to EXT-20, "Removal and Installation".

3. Remove air duct and air cleaner case.

• MR16DDT: Refer to EM-26, "Removal and Installation". • HR16DE: Refer to EM-161, "Removal and Installation".

• K9K: Refer to EM-280, "Removal and Installation".

4. Remove brake master cylinder assembly. Refer to BR-42, "Removal and Installation".

5. Remove vacuum hose from brake booster.

• MR16DDT: Refer to BR-49, "MR16DDT : Removal and Installation". • HR16DE: Refer to BR-50, "HR16DE : Removal and Installation".

• K9K: Refer to BR-52, "K9K : Removal and Installation".

6. Remove snap pin (1) and clevis pin (2). Refer to BR-20, "Exploded View".

7. Remove nuts on brake booster and brake pedal assembly.

CAUTION:
Hold the brake booster so as to avoid dropping out.

8. Remove brake booster and spacer.

NOT

E:
If removing brake booster is difficult, remove clevis from brake booster.

9. Remove vacuum pipe from brake booster. (2WD)

9. Remove vacuum pipe from brake booster. (2WD) 10. Remove spacer from brake booster.

11. Perform inspection after removal. Refer to BR-47, "Inspection and Adjustment".

INSTALLATION

CAUTION:
Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface.

Note the following, and install in the reverse order of removal.

• Set vacuum pipe angle (A) as shown in the figure. (2WD)

A : 50 – 60°

• Be careful not to damage brake booster stud bolt threads. If brake booster is tilted during installation, the dash panel may damage the threads. • Never deform or bend the brake tubes when installing the brake booster. • Always use a gasket between the brake booster and the spacer. • Replace the clevis pin if it is damaged. Refer to BR-22, "Inspection and Adjustment". • Perform the air bleeding. Refer to BR-13, "Bleeding Brake System".

• Check each item of brake pedal. Adjust it if the measurement value is not the standard. Refer to BR-9, "Inspection and Adjustment".

Inspection and Adjustmen

Inspection and Adjustmen

INSPECTION BEFORE REMOVAL

Air Tight

CAUTION:
Check the air tight condition when the master cylinder and the brake booster is installed.

1. Check the air tight use a handy vacuum pump.

At vacuum of −66.7 kPa (−500 mmHg, −19.69 inHg, −0.067 bar) : Vacuum should decrease within 3.3 kPa (24.8 mmHg, 0.98 inHg, 0.033 bar) for 15 seconds.

2. If the air tight condition cannot be maintained, perform the following operation.

a. Check the no dirt and dust are present on the brake booster and brake master cylinder mating faces.

Clean it if necessary. b. Check the O-ring on the master cylinder. If anything is found, replace the O-ring. Refer to BR-42, "Removal and Installation".

c. Check the air tight condition again. If the condition still cannot be maintained, replace the brake booster.

INSPECTION AFTER REMOVAL

Input Rod Length Inspection 1. Loosen the lock nut (1) and adjust the input rod (2) to the specified length (A).

A : Refer to BR-70, "Brake Booster".

2. Tighten the lock nut to the specified torque.

INSPECTION AFTER INSTALLATION

INSPECTION AFTER INSTALLATION

Operation
Depress the brake pedal several times at 5-second intervals with the engine stopped. Start the engine with the brake pedal fully depressed. Check that the clearance between brake pedal and dash lower panel decreases.

NOTE

:
A slight impact with a small click may be felt on the pedal when the brake pedal is fully depressed. This is a normal phenomenon due to the brake system operation.

Air Tight
1. Run the engine at idle for 1 minute to apply vacuum to the brake booster, and stop the engine. 2. Depress the brake pedal several times at 5-second intervals until the accumulated vacuum is released to atmospheric pressure. Check that the clearance between brake pedal and dash lower panel gradually increases each time the brake pedal is depressed when performing this operation.

3. Depress the brake pedal with the engine running. Then stop the engine while holding down the brake pedal. Check that the brake pedal stroke does not change after holding down the brake pedal for 30 seconds or more.

ADJUSTMENT AFTER INSTALLATION

Perform the brake pedal adjustment after installing the brake pedal assembly. Refer to BR-9, "Inspection and Adjustment".