Brake Control System without ESP

C1105, C1106, C1107, C1108 wheel sensor

In this manual: Brake Control System without ESP
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~9min read

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

1. Stat the engine.With CONSULT-III.


1. Stat the engine. 2. Drive the vehicle at approx. 30 km/h or more for approx. 1 minute. 3. Stop the vehicle.

4. Perform self-diagnosis for “ABS”.

Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected? YES >> Proceed to BRC-40, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

CAUTION:
Never check between wheel sensor harness connector terminals.
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY SYSTEM

Check ABS actuator and electric unit (control unit) power supply system. Refer to BRC-64, "Diagnosis Procedure".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace error-detected parts.

2.CHECK TIRE 1. Turn the ignition switch OFF.

2. Check tire air pressure, wear and size. Refer to WT-9, "Tire Air Pressure".

Is the inspection result normal? YES >> GO TO 5.

NO >> Adjust air pressure or replace tire and GO TO 3.

3.CHECK DATA MONITOR (1)

1. Erase Self-diagnosis result for “ABS”.With CONSULT-III.


1. Erase Self-diagnosis result for “ABS”. 2. Turn the ignition switch OFF, and wait 10 seconds or more. 3. Stat the engine.

4. Select “ABS” and “DATA MONITOR”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and “RR RH SENSOR”.

NOTE

:
Set the “DATA MONITOR” recording speed to “10 msec”.

5. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.

Regarding the deference at 30 km/h between the wheel speed detected by the error detecting wheel sensor and the maximum/minimum wheel speed detected by the normal wheel sensors, is the difference within 5%, respectively? YES >> GO TO 4.

NO >> GO TO 5.

4.PERFORM SELF-DIAGNOSIS (1)

1. Drive the vehicle at approx. 30 km/h (19 MPH) or more for approx. 1With CONSULT-III.


1. Drive the vehicle at approx. 30 km/h or more for approx. 1 minute. 2. Stop the vehicle.

3. Perform self-diagnosis for “ABS”.

Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected? YES >> GO TO 5.

NO >> INSPECTION END

5.CHECK WHEEL SENSOR 1. Turn the ignition switch OFF. 2. Check wheel sensor for damage.

3. Remove dust and foreign matter adhered to the sensor rotor with a vacuum dust collector through the wheel sensor mounting hole.

CAUTION:
Install wheel sensor with no backlash and float, and tighten the mounting bolt to the specified torque.
• Front: Refer to BRC-84, "FRONT WHEEL SENSOR : Exploded View".

• Rear: Refer to BRC-85, "REAR WHEEL SENSOR : Exploded View".

Is the inspection result normal? YES >> GO TO 8.

NO >> GO TO 6.

6.REPLACE WHEEL SENSOR (1)

1. Replace wheel sensor.With CONSULT-III.


1. Replace wheel sensor.

- Front: Refer to BRC-84, "FRONT WHEEL SENSOR : Removal and Installation".

- Rear: Refer to BRC-86, "REAR WHEEL SENSOR : Removal and Installation".

2. Erase Self-diagnosis result for “ABS”. 3. Turn the ignition switch OFF, and wait 10 seconds or more. 4. Stat the engine.

5. Select “ABS” and “DATA MONITOR”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and “RR RH SENSOR”.

NOTE

:
Set the “DATA MONITOR” recording speed to “10 msec”.

6. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.

Regarding the deference at 30 km/h between the wheel speed detected by the error detecting wheel sensor and the maximum/minimum wheel speed detected by the normal wheel sensors, is the difference within 5%, respectively? YES >> GO TO 7.

NO >> GO TO 19.

7.PERFORM SELF-DIAGNOSIS (2)

1. Drive the vehicle at approx. 30 km/h (19 MPH) or more for approx. 1With CONSULT-III.


1. Drive the vehicle at approx. 30 km/h or more for approx. 1 minute. 2. Stop the vehicle.

3. Perform self-diagnosis for “ABS”.

Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected? YES >> GO TO 19.

NO >> INSPECTION END

8.CHECK CONNECTOR 1. Turn the ignition switch OFF. 2. Check ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

3. Check wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal? YES >> GO TO 11.

NO >> Repair or replace error-detected parts, securely lock the connector, and GO TO 9.

9.CHECK DATA MONITOR (2)

1. Erase Self-diagnosis result for “ABS”.With CONSULT-III.


1. Erase Self-diagnosis result for “ABS”. 2. Turn the ignition switch OFF, and wait 10 seconds or more. 3. Stat the engine.

4. Select “ABS” and “DATA MONITOR”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and “RR RH SENSOR”.

NOTE

:
Set the “DATA MONITOR” recording speed to “10 msec”.

5. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.

Regarding the deference at 30 km/h between the wheel speed detected by the error detecting wheel sensor and the maximum/minimum wheel speed detected by the normal wheel sensors, is the difference within 5%, respectively? YES >> GO TO 10.

NO >> GO TO 11.

10.PERFORM SELF-DIAGNOSIS (3)

1. Drive the vehicle at approx. 30 km/h (19 MPH) or more for approx. 1With CONSULT-III.


1. Drive the vehicle at approx. 30 km/h or more for approx. 1 minute. 2. Stop the vehicle.

3. Perform self-diagnosis for “ABS”.

Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected? YES >> GO TO 11.

NO >> INSPECTION END

11.CHECK TERMINAL 1. Turn the ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) harness connector and then check ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with harness connector.

3. Disconnect wheel sensor harness connector and check each wheel sensor pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> GO TO 14.

NO >> Repair or replace error-detected parts and GO TO 12.

12.CHECK DATA MONITOR (3)

1. Connect ABS actuator and electric unit (control unit) harness connector.With CONSULT-III.


1. Connect ABS actuator and electric unit (control unit) harness connector. 2. Connect wheel sensor harness connector. 3. Erase Self-diagnosis result for “ABS”. 4. Turn the ignition switch OFF, and wait 10 seconds or more. 5. Stat the engine.

6. Select “ABS” and “DATA MONITOR”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and “RR RH SENSOR”.

NOTE

:
Set the “DATA MONITOR” recording speed to “10 msec”.

7. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.

Regarding the deference at 30 km/h between the wheel speed detected by the error detecting wheel sensor and the maximum/minimum wheel speed detected by the normal wheel sensors, is the difference within 5%, respectively? YES >> GO TO 13.

NO >> GO TO 14.

13.PERFORM SELF-DIAGNOSIS (4)

1. Drive the vehicle at approx. 30 km/h (19 MPH) or more for approx. 1With CONSULT-III.


1. Drive the vehicle at approx. 30 km/h or more for approx. 1 minute. 2. Stop the vehicle.

3. Perform self-diagnosis for “ABS”.

Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected? YES >> GO TO 14.

NO >> INSPECTION END

14.CHECK WHEEL SENSOR HARNESS 1. Turn the ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) harness connector. 3. Disconnect wheel sensor harness connector.

4. Check continuity between ABS actuator and electric unit (control unit) harness connector and the ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 15.

NO >> Repair or replace error-detected parts and GO TO 15.

15.CHECK DATA MONITOR (4)

1. Connect ABS actuator and electric unit (control unit) harness connector.With CONSULT-III.


1. Connect ABS actuator and electric unit (control unit) harness connector. 2. Connect wheel sensor harness connector. 3. Erase Self-diagnosis result for “ABS”. 4. Turn the ignition switch OFF, and wait 10 seconds or more. 5. Stat the engine.

6. Select “ABS” and “DATA MONITOR”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and “RR RH SENSOR”.

NOTE

:
Set the “DATA MONITOR” recording speed to “10 msec”.

7. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.

Regarding the deference at 30 km/h between the wheel speed detected by the error detecting wheel sensor and the maximum/minimum wheel speed detected by the normal wheel sensors, is the difference within 5%, respectively? YES >> GO TO 16.

NO >> GO TO 17.

16.PERFORM SELF-DIAGNOSIS (5)

1. Drive the vehicle at approx. 30 km/h (19 MPH) or more for approx. 1With CONSULT-III.


1. Drive the vehicle at approx. 30 km/h or more for approx. 1 minute. 2. Stop the vehicle.

3. Perform self-diagnosis for “ABS”.

Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected? YES >> GO TO 17.

NO >> INSPECTION END

17.REPLACE WHEEL SENSOR

1. Replace wheel sensor.With CONSULT-III.


1. Replace wheel sensor.

- Front: Refer to BRC-84, "FRONT WHEEL SENSOR : Removal and Installation".

- Rear: Refer to BRC-86, "REAR WHEEL SENSOR : Removal and Installation".

2. Erase Self-diagnosis result for “ABS”. 3. Turn the ignition switch OFF, and wait 10 seconds or more. 4. Stat the engine.

5. Select “ABS” and “DATA MONITOR”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and “RR RH SENSOR”.

NOTE

:
Set the “DATA MONITOR” recording speed to “10 msec”.

6. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.

Regarding the deference at 30 km/h between the wheel speed detected by the error detecting wheel sensor and the maximum/minimum wheel speed detected by the normal wheel sensors, is the difference within 5%, respectively? YES >> GO TO 18.

NO >> GO TO 19.

18.PERFORM SELF-DIAGNOSIS (6)

1. Drive the vehicle at approx. 30 km/h (19 MPH) or more for approx. 1With CONSULT-III.


1. Drive the vehicle at approx. 30 km/h or more for approx. 1 minute. 2. Stop the vehicle.

3. Perform self-diagnosis for “ABS”.

Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected? YES >> GO TO 19.

NO >> INSPECTION END

19.REPLACE SENSOR ROTOR

1. Replace sensor rotor.With CONSULT-III.


1. Replace sensor rotor.

- Front: Refer to BRC-84, "FRONT WHEEL SENSOR : Removal and Installation".

- Rear: Refer to BRC-86, "REAR WHEEL SENSOR : Removal and Installation".

2. Erase Self-diagnosis result for “ABS”. 3. Turn the ignition switch OFF, and wait 10 seconds or more. 4. Stat the engine. 5. Drive the vehicle at approx. 30 km/h or more for approx. 1 minute. 6. Stop the vehicle.

7. Perform self-diagnosis for “ABS”.

Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-90, "Removal and Installation".

NO >> INSPECTION END