Transaxle & transmission 5MT: RS5F92R

Mainshaft and gear

In this manual: Transaxle & transmission 5MT: RS5F92R
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~6min read

Exploded View

1. Mainshaft front bearing outer

1. Mainshaft front bearing outer race
2. Mainshaft front bearing inner race 3. Mainshaft
4. 1st main gear
5. 1st inner baulk ring 6. 1st synchronizer cone 7. 1st outer baulk ring 8. Spread spring
9. 1st-2nd synchronizer hub 10. 1st-2nd coupling sleeve 11. 2nd outer baulk ring 12. 2nd synchronizer cone 13. 2nd inner baulk ring 14. Mainshaft bushing
15. 2nd main gear
16. Thrust washer
17. 3rd main gear
18. 3rd baulk ring
19. 3rd-4th synchronizer hub 20. 3rd-4th coupling sleeve 21. Spring
22. Insert key
23. 4th baulk ring
24. 4th main gear
25. Adjusting shim
26. Mainshaft rear bearing inner race 27. Mainshaft rear bearing outer race 28. 5th main gear

: Apply Thread Locking Sealant,: Apply gear oil.
Loctite Frenbloc or an equivalent.: Apply Thread Locking Sealant,
Loctite Frenbloc or an equivalent. : Always replace after every: Replace the parts as a set.
disassembly.: Always replace after every
disassembly. : N·m (kg-m, ft-lb): Select with proper thickness.


Disassembly: N·m (kg-m, ft-lb)


Disassembly

CAUTION:
Place a direction mark on the surface of gears, avoiding an effect on their functions.

1. Set puller (A) at the area shown by () on the 3rd main gear
) on the 3rd main gear (1).

2. Remove the 3rd main gear, using a press. The following parts: 3rd baulk ring side


2. Remove the 3rd main gear, using a press. The following parts become detached together at the same time: • Mainshaft bushing
• 3rd-4th synchronizer hub • 3rd baulk ring

CAUTION:
Never drop mainshaft.
3. Set puller (A) to 1st main gear (1).

3. Set puller (A) to 1st main gear (1).

4. Remove the 1st main gear, using a press. The following parts become detached together at the same time: • Mainshaft bushings
• Thrust washer
• 2nd main gear
• 2nd inner baulk ring
• 2nd synchronizer cone
• 2nd outer baulk ring
• 1st-2nd coupling sleeve • 1st-2nd synchronizer hub • 1st outer baulk ring
• 1st synchronizer cone
• 1st inner baulk ring

CAUTION:
Never drop mainshaft.
5. Remove spread springs from 1st-2nd synchronizer hub.

6. Remove mainshaft front bearing inner race, using a puller [Commercial service tool].

Assembly

Assembly

CAUTION:
After replacing the following parts, adjust mainshaft rear bearing preload. Refer to TM-51, "Inspection and Adjustment".

• Mainshaft
• Mainshaft front bearing inner race • Mainshaft front bearing outer race • Mainshaft rear bearing inner race • Mainshaft rear bearing outer race • Clutch housing
• Transaxle case

1. Install 1st main gear to mainshaft.

2. Apply gear oil to 1st inner baulk ring, 1st synchronizer cone, and 1st outer baulk ring.

CAUTION:
Replace 1st inner baulk ring, 1st synchronizer cone, and 1st outer baulk ring as a set.

3. Install 1st inner baulk ring (1), 1st synchronizer cone (2), and 1st outer baulk ring (3) to 1st main gear (4).

CAUTION:
Align the pawl (A) of the 1st synchronizer cone with the groove (B) of the 1st main gear.
4. Install spread spring to 1st-2nd synchronizer hub.

5. Install 1st-2nd synchronizer hub to mainshaft.

CAUTION:
Replace 1st-2nd synchronizer hub and 1st-2nd coupling sleeve as a set.
6. Heat the mainshaft bushing for 15 minutes at a temperature of

6. Heat the mainshaft bushing for 15 minutes at a temperature of 150 °C, using a heat plate or an equivalent.

CAUTION:
• Never reuse mainshaft bushing.

• Never touch the mainshaft bushing with bare hands.

7. Remove the mainshaft bushing from the heat plate to install to the mainshaft, using pliers or an equivalent.

CAUTION:
Never touch the mainshaft bushing with bare hands.
8. Install mainshaft bushing (1) to mainshaft, using a drift (A) [Commercial

8. Install mainshaft bushing (1) to mainshaft, using a drift (A) [Commercial service tool] and a press.

2 : 1st-2nd synchronizer hub

9. Install 1st-2nd coupling sleeve and spread spring to 1st-2nd synchronizer hub.

CAUTION:
Replace 1st-2nd synchronizer hub and 1st-2nd coupling sleeve as a set.

10. Apply gear oil to 2nd inner baulk ring, 2nd synchronizer cone, and 2nd outer baulk ring.

CAUTION:
Replace 2nd inner baulk ring, 2nd synchronizer cone, and 2nd outer baulk ring as a set.
11. Install 2nd inner baulk ring, 2nd synchronizer cone, and 2nd outer baulk ring to 1st-2nd synchronizer hub.

12. Install 2nd main gear and thrust washer to mainshaft.

CAUTION:
Align the pawl of the 2nd synchronizer cone with the groove of the 2nd main gear.
13. Heat the mainshaft bushing for 15 minutes at a temperature of

13. Heat the mainshaft bushing for 15 minutes at a temperature of 150 °C, using a heat plate or an equivalent.

CAUTION:
• Never reuse mainshaft bushing.

• Never touch the mainshaft bushing with bare hands.

14. Remove the mainshaft bushing from the heat plate to install to the mainshaft, using pliers or an equivalent.

CAUTION:
Never touch the mainshaft bushing with bare hands.
15. Install mainshaft bushing (1) to mainshaft, using a drift (A) [Commercial

15. Install mainshaft bushing (1) to mainshaft, using a drift (A) [Commercial service tool] and a press.

2 : Thrust washer
3 : 2nd main gear

16. Install 3rd main gear to mainshaft. 17. Apply gear oil to 3rd baulk ring. 18. Install 3rd baulk ring to 3rd main gear.

19. Install 3rd-4th synchronizer hub to mainshaft.

CAUTION:
Replace 3rd-4th synchronizer hub and 3rd-4th coupling sleeve as a set.
20. Heat the mainshaft bushing for 15 minutes at a temperature of

20. Heat the mainshaft bushing for 15 minutes at a temperature of 150 °C, using a heat plate or an equivalent.

CAUTION:
• Never reuse mainshaft bushing.

• Never touch the mainshaft bushing with bare hands.

21. Remove the mainshaft bushing from the heat plate to install to the mainshaft, using pliers or an equivalent.

CAUTION:
Never touch the mainshaft bushing with bare hands.
22. Install mainshaft bushing (1) to mainshaft, using a drift (A) [Commercial

22. Install mainshaft bushing (1) to mainshaft, using a drift (A) [Commercial service tool] and a press.

2 : 3rd-4th synchronizer hub

23. Install mainshaft front bearing inner race, using a drift [Commercial service tool].

CAUTION:
• Never reuse mainshaft front bearing inner race.

• Replace mainshaft front bearing inner race and mainshaft front bearing outer race as a set.

Inspection

Inspection

INSPECTION AFTER DISASSEMBLY

Mainshaft and Gear
Check the following items and replace if necessary.

• Damage, peeling, bend, uneven wear, and distortion of shaft.

• Excessive wear, damage, and peeling of gear.

Synchronizer Hub and Coupling Sleeve

Synchronizer Hub and Coupling Sleeve Check the following items and replace if necessary.

• Breakage, damage, and unusual wear on contact surface of coupling sleeve, synchronizer hub, and insert key.

• Coupling sleeve and synchronizer hub move smoothly.

Baulk Ring

Baulk Ring
Check contact surface of baulk ring cam and insert key for excessive wear, uneven wear, bend, and damage. Replace if necessary.

Bearing

Bearing
Check bearing for damage and unsmooth rotation. Replace if necessary.

Final drive