Transaxle & transmissioN CVT: RE0F11A

Unit removal and installation

In this manual: Transaxle & transmissioN CVT: RE0F11A
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~4min read
0204060801005138N·mlb·ft
Tightening torque found on this page

TRANSMISSION ASSEMBLY

Exploded View
1. Transaxle assembly

1. Transaxle assembly

A: : For the tightening torque, refer to TM-508, "Removal and Installation".

Removal and Installation

REMOVAL

WARNING:
Never open the radiator cap or drain plug when the engine is hot. Hot liquid may spray out, causing serious injury.
CAUTION:
Perform these steps after the coolant temperature has cooled sufficiently.
NOTE: • When replacing the TCM and transaxle assembly as a set, replace the transaxle assembly first and then replace the TCM. Refer to TM-374, "Description".

• Cap or plug openings to prevent fluid from spilling.

1. Remove the battery. Refer to PG-124, "Exploded View". 2. Remove the air cleaner case. Refer to EM-161, "Removal and Installation". 3. Remove the ECM and bracket as a set.

4. Disconnect the connectors and harnesses.

• For CVT unit connector, refer to TM-311, "Removal and Installation Procedure for CVT Unit Connector".

• Transmission position switch connector • Primary pulley speed sensor connector • Secondary pulley speed sensor connector • Output speed sensor connector • Ground

5. Disconnect the control cable from the transaxle assembly. Refer to TM-485, "Removal and Installation".

6. Remove the water hose from the engine side. TM-500, "Removal and Installation".

NOTE

:
Coolant leaks out. Use a cap, plug, or other means to prevent leakage.

7. Remove starter motor. Refer to STR-22, "HR16DE : Removal and Installation". 8. Remove the left and right fender protector. Refer to EXT-22, "Removal and Installation".

9. Rotate the crankshaft and remove the nuts that secure the drive plate to the torque converter from the stator motor mount.

CAUTION:
Rotate crankshaft clockwise (as viewed from the front of the engine).
10. Remove the left and right drive shafts. Refer to FAX-53, "Removal and Installation". 11. Remove the front suspention member. Refer to FSU-18, "Removal and Installation". 12. Remove the heat insulator. Refer to EX-12, "Exploded View".

13. Set a transmission jack under the transaxle assembly.

CAUTION:
Be careful not to contact the drain plug when setting the transmission jack.

14. Set a transmission jack under the engine assembly.

CAUTION:
Be careful not to contact the drain plug when setting the transmission jack.
15. Remove the left engine mounting insulator and left engine mounting bracket as a set. Refer to EM-215, "Exploded View". 16. Remove the bolts that fasten the transaxle assembly and engine assembly.

17. Remove the transaxle assembly from the vehicle.

CAUTION:
Never drop the torque converter.

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:
• Never reuse O-ring.

• Apply Vaseline to the O-ring.

• When installing the transaxle assembly onto the engine assembly, check the engagement of the dowel pin ().
).

• When using drive plate location guide, install drive plate location

• When using drive plate location guide, install drive plate location guide (Commercial service tool: 31197EU50A) (A) to drive plate location guide mounting part of torque converter.

• Rotate the crankshaft so that the drive plate location guide insert

• Rotate the crankshaft so that the drive plate location guide insert hole (A) of the drive plate is aligned with the drive plate location guide that is installed on the torque converter.

CAUTION:
• Rotate the crankshaft clockwise (as viewed from the front of the engine).

• Be careful that torque converter stud bolt is aligned to drive plate hole position. Otherwise stud bolt contacts drive plate.

• Temporally tighten drive plate and torque converter connecting nuts and tighten to the specified torque.

Tightening torque : 51 N·m

CAUTION:

CAUTION:
• Rotate crankshaft clockwise (as viewed from the front of the engine).

• Check the tightening torque for the crankshaft pulley mounting bolts after the bolts fastening the drive plate and torque converter have been tightened and the crankshaft pulley mounting bolts have been secured. Refer to EM-182, "Removal and Installation".

• Install the transaxle assembly and engine assembly mounting bolts according to the following standards.


Inspection and Adjustment

Inspection and Adjustment

INSPECTION BEFORE INSTALLATION

Check the distance “A”between the converter housing and torque converter.

B : Scale
C : Straightedge

Dimension “A” : TM-513, "Torque Converter"

INSPECTION AFTER INSTALLATION

INSPECTION AFTER INSTALLATION

Check the following items: • CVT fluid leakage. Refer to TM-480, "Inspection" • For CVT position, refer to TM-383, "Inspection and Adjustment".

• Start the engine and check for coolant leakage from the parts which are removed and reinstalled.

ADJUSTMENT AFTER INSTALLATION

• Adjust the CVT fluid level. TM-379, "Adjustment".

• Perform "ADDITIONAL SERVICE WHEN REPLACE TRANSAXLE ASSEMBLY". Refer to TM-375, "Description".