Brakes

Diagnosis and Repair Work Flow

11steps
~66min
4/5difficulty
Done 0 of 11
Work Flow

DETAILED FLOW

INTERVIEW THE CUSTOMER

Clarify customer concerns before inspection. First of all, perform an interview utilizing Diagnostic Work Sheet and reproduce the symptom as well as fully understand it. Ask customer about his/her concerns carefully. Check symptoms by driving Nissan Murano vehicle with customer, if necessary.

>>

GO TO 2.

CHECK SYMPTOM

Reproduce the symptom that is indicated by the customer, based on the information from the customer obtained in the interview. Also check that the symptom is not caused by fail-safe mode. Refer to Fail-Safe.

>>

GO TO 3.

PERFORM SELF DIAGNOSTIC RESULT

CONSULT

  1. Ignition switch OFF → ON.

  2. Select “Self Diagnostic Result” mode of “ABS”.

Is DTC detected?

YES>>

Record or print Self Diagnostic Results and Freeze Frame Data (FFD). GO TO 4.

NO>>

GO TO 6.

RECHECK THE SYMPTOM

CONSULT

  1. Erase the memory of “Self Diagnostic Result” mode of “ABS”.

  2. Ignition switch OFF → ON → OFF.

  3. Perform DTC confirmation procedures for the malfunctioning system.

Is DTC detected?

YES>>

GO TO 5.

NO>>

Check harness and connectors based on the information obtained in the interview. Refer to Intermittent Incident.

REPAIR OR REPLACE MALFUNCTIONING COMPONENT

  1. Repair or replace malfunctioning components.

  2. Reconnect component or connector after repairing or replacing.

  3. When DTC is detected, erase the memory of “Self Diagnostic Result” mode of “ABS”.

>>

GO TO 7.

IDENTIFY MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS

Identify malfunctioning system based on symptom diagnosis and perform inspection.

Can the malfunctioning system be identified?

YES>>

GO TO 7.

NO>>

Check harness and connectors based on the information obtained in the interview. Refer to Intermittent Incident.

FINAL CHECK

CONSULT

  1. Select “Data Monitor” mode of “ABS”.

  2. Check the reference values. Refer to Values on the Diagnosis Tool.

  3. Recheck the symptom and check that the symptom is not reproduced on the same conditions.

Is the symptom reproduced?

YES>>

GO TO 3.

NO>>

Inspection End.

Diagnostic Work Sheet

DESCRIPTION

  • In general, customers have their own criteria for a problem. Therefore, it is important to understand the symptom and status well enough by asking the customer about his/her concerns carefully. To systemize all the information for the diagnosis, prepare the interview sheet referring to the interview points.

  • In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.

INTERVIEW SHEET SAMPLE

Interview sheet
Customer nameMR/MSRegistration numberInitial year registration
Nissan Murano Vehicle typeVIN
Storage dateEngine/traction MotorMileagekm (Mile)
Symptom □ Does not operate ( ) function

□ Warning lamp turns ON.

□ or □ or □□

□ Other ( )
□ Noise (Location: ) □ Vibration (Location: )
□ Other ( )
First occurrence □ Recently □ Other ( )
Frequency of occurrence □ Always □ Under a certain conditions of □ Sometimes ( time(s)/day)
Climate conditions □ Irrelevant
Weather □ Fine □ Cloud □ Rain □Snow □ Others ( )
Temperature □ Hot □Warm □ Cool □ Cold □ Temperature [Approx. °C (°F)]
Relative humidity □ High □ Moderate □ Low
Road conditions □ Ordinary road □ Highway □ Mountainous road (uphill or downhill) □ Rough road
Operating condition, etc.

□ Irrelevant

□ When engine/traction motor starts □ During idling

□ During driving □ During acceleration □ At constant speed driving

□ During deceleration

□ Immediately before stop [Nissan Murano Vehicle speed: Approx. km/h (MPH)]

□ During cornering (right curve or left curve)

□ When steering wheel is steered (to right or to left)
Other conditions VDC OFF switch operation □ Yes □ No

Use of other functions

(ex. ICC)
□ Yes □ No ( )
Presence of non-genuine parts installation □ Yes □ No ( )

Memo