Moonroof Motor Assembly
BCM supplies the moonroof motor assembly with power.
CPU is integrated in moonroof motor assembly.
Tilts up/down & slides open/close by moonroof switch operation.
In order to close the moonroof during high speed driving, the Combination meter will send a speed signal to the moonroof CPU to adjust the torque of the motor during the tilt-down operation.
CHECK MOONROOF MOTOR FUNCTION
Does the tilt up/down & slide open/close functions operate normally with moonroof switch?
Is the inspection result normal?
YES>>Moonroof motor assembly is OK.
NO>>Refer to Diagnosis Procedure.
CHECK POWER SUPPLY CIRCUIT
Ignition switch OFF.
Disconnect the moonroof motor assembly connector.
Ignition switch ON.
Check voltage between moonroof motor assembly harness connector and ground.
(+) (–) Voltage
(Approx.)Moonroof motor assembly Connector Terminal R4 1 Ground Battery voltage 6
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace harness.
CHECK GROUND CIRCUIT
Ignition switch OFF.
Check continuity between moonroof motor assembly harness connector and ground.
Moonroof motor assembly — Continuity Connector Terminal R4 5 Ground Yes
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness.
CHECK MOONROOF SWITCH INPUT SIGNAL
Connect moonroof motor assembly.
Ignition switch ON.
Check voltage between the moonroof motor assembly connector and ground.
(+) (–) Condition Voltage
(Approx.)Moonroof motor assembly Connector Terminals R4 7 Ground Moonroof switch is operated
TILT DOWN or SLIDE OPEN0 V Other than above Battery voltage 8 Moonroof switch is operated
TILT UP or SLIDE CLOSE0 V Other than above Battery voltage
Is the inspection result normal?
YES>>GO TO 6.
NO>>GO TO 4.
CHECK MOONROOF SWITCH CIRCUIT
Ignition switch OFF.
Disconnect the moonroof motor assembly connector and moonroof switch connector.
Check continuity between the moonroof motor assembly harness connector and moonroof switch harness connector.
Moonroof motor assembly Moonroof switch Continuity Connector Terminal Connector Terminal R4 7 R9 1 Yes 8 8 Check continuity between the moonroof motor assembly harness connector and ground.
Moonroof motor assembly — Continuity Connector Terminal R4 7 Ground No 8
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace harness.
CHECK MOONROOF SWITCH GROUND CIRCUIT
Check continuity between the moonroof switch harness connector and ground.
| Moonroof switch | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| R9 | 6 | Ground | Yes |
Is the inspection result normal?
YES>>Refer to Component Inspection.
NO>>Repair or replace harness.
CHECK COMBINATION METER SIGNAL
Check the signal between the moonroof motor assembly harness connector and ground with oscilloscope.
| (+) | (-) | Condition | Signal (Reference value) | |
|---|---|---|---|---|
| Moonroof motor assembly | ||||
| Connector | Terminal | |||
| R4 | 4 | Ground | Speedometer operated [When Nissan Murano vehicle speed is approx. 40 km/h] | ![]() |
Is the inspection result normal?
YES>>Replace moonroof motor assembly. Refer to Removal and Installation.
NO>>GO TO 7.
CHECK COMBINATION METER CIRCUIT
Ignition switch OFF.
Disconnect combination meter connector and moonroof motor assembly connector.
Check continuity between combination meter harness connector and the moonroof motor assembly harness connector.
Combination meter Moonroof motor assembly Continuity Connector Terminal Connector Terminal M24 38 R4 4 Yes Check continuity between the combination meter harness connector and ground.
| Combination meter | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M24 | 38 | Ground | No |
Is the inspection result normal?
YES>>Replace combination meter. Refer to Removal and Installation.
NO>>Repair or replace harness.
