Rear Axle :: Unit Disassembly and Assembly. Rear Drive Shaft

| 1. | Boot band | 2. | Circular clip | 3. | Dust shield |
| 4. | Housing | 5. | Snap ring | 6. | Spider assembly |
| 7. | Boot | 8. | Shaft | 9. | Joint sub-assembly |
| 10. | Circular clip | Wheel side |
DISASSEMBLY
Wheel Side
Secure rear drive shaft in a vise.
Remove and discard boot bands and slide boot back.
Install suitable tool (A) 30 mm (1.18 in) or more into the threaded part of joint sub-assembly, and pull joint sub-assembly from shaft using suitable tool (B).

Remove and discard circular clip from shaft.
Remove and discard boot from shaft.
While rotating ball cage, clean old grease off joint sub-assembly.
Final Drive Side
Secure rear drive shaft in a vise.
Remove and discard boot bands and slide boot back.
Put matching marks on housing and shaft before separating housing from shaft.
Put matching marks (A) on spider assembly and shaft.

Remove and discard snap ring (1) using a suitable tool.

Remove spider assembly from shaft.
Remove and discard boot from shaft.
Remove and discard circular clip from housing.
Remove and discard dust shield from housing.
Clean old grease off housing and shaft.
INSPECTION AFTER DISASSEMBLY
Shaft
Replace entire rear drive shaft if there is any bending, cracking, or other damage.
Joint Sub-assembly
Make sure there is no rough rotation or unusual axial looseness.
Make sure there is no foreign material inside joint sub-assembly.
Check joint sub-assembly for compression scars, cracks or fractures.
If there are any irregular conditions of joint sub-assembly components, replace entire rear drive shaft.
Housing and Spider Assembly
If roller surface of spider assembly has scratches or wear, replace entire rear drive shaft.
ASSEMBLY
Wheel Side
Insert Genuine NISSAN Grease into joint sub-assembly (1) until grease begins to ooze from ball groove and serration hole.

Install new boot and new small boot band to shaft.

Remove protective tape wrapped around the drive shaft serration.
Attach new circular clip to shaft. Circular clip must fit securely into shaft groove. Attach nut to joint sub-assembly. Use a suitable tool to press-fit.
Install joint sub-assembly to shaft using suitable tool.

Pull the joint sub-assembly in the axial direction away from the shaft. Confirm that the joint sub-assembly cannot be pulled out.
Insert remaining balance of the specified amount of Genuine NISSAN Grease listed below into housing from large diameter side of boot.
| Grease quantity | : Refer to Drive Shaft. |
Install boot securely into grooves (indicated by “*” marks) as shown.

To prevent deformation of boot, adjust boot installation length (L) to specified value indicated below. Insert a suitable tool into large end of boot. Bleed air from boot to prevent boot deformation.
Boot installation length (L) : Refer to Drive Shaft.
Install new boot bands securely.
Put boot band in groove on drive shaft boot. Then fit pawls (

After installing joint sub-assembly and shaft, make sure that they are in the correct position when rotating boot. If boot position is not correct, remove old boot bands, then reposition boot and secure with new boot bands.
Final Drive Side
Install new boot and new small boot band to shaft.

Remove protective tape wrapped around the drive shaft serration.
Align matching marks (A) on spider assembly (1) with matching mark on shaft (2). Install spider assembly to shaft with chamfer (B) facing shaft.

Install new snap ring (1) onto shaft using suitable tool.

Pack housing with the specified amount of new Genuine NISSAN Grease.
| Grease amount | : Refer to Drive Shaft. |
Align matching marks made during disassembly and install housing onto spider assembly.
After installation, pull shaft to check engagement between housing and snap ring.
Install boot securely into grooves (indicated by “*” marks) as shown.

Make sure boot installation length (L) is length specified below. Insert a suitable tool into large end of boot. Bleed air from boot to prevent boot deformation.
| Boot installation length (L) | : Refer to Drive Shaft. |
Install new boot bands securely.
Put boot band in groove on drive shaft boot. Then fit pawls (

After installing housing and shaft, make sure that they are in the correct position when rotating boot. If boot position is not correct, remove old boot bands, then reposition boot and secure with new boot bands.
Install a new dust shield.
Install a new circular clip.