Body Exterior, Doors, Roof & Vehicle Security

Service Data and Specifications (sds). Body Alignment

~4min read
Body Center Marks

Factory marks exist on certain parts of the body to indicate the vehicle center. When repairing the Nissan Murano vehicle frame (members, pillars, etc.) damaged in an accident the most accurate and effective repair will be achieved by using these marks together with body alignment specifications.

Front
PointsPortionMarks
A Front roof Embossment
B Center cowl top Hole
C Body side Notch
D Rear roof Notch
Description
  • All dimensions indicated in the figures are actual.

  • When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge itself to make sure there is no free play.

  • When a measuring tape is used, check to be sure there is no elongation, twisting or bending.

  • Measurements should be taken at the center of the mounting holes.

  • An asterisk (*) following the value at the measuring point indicates that the measuring point on the other side is symmetrically the same value.

  • The coordinates of the measurement points are the distances measured from the standard line of ″X″, ″Y″ and ″Z″.

  • ″Z″: Imaginary base line [200 mm (7.87 in) below datum line (″0Z″ at design plan)]

1. Nissan Murano Vehicle center 2. Front axle center 3. Imaginary base line
Engine Compartment

MEASUREMENT

Dimensions marked with ″*″ indicate symmetrically identical dimensions on both the RH and LH sides of the Nissan Murano vehicle.

Unit: mm (in)

MEASUREMENT POINTS

Unit: mm (in)

PointsCoordinatesRemarks
XYZ
A, a ±566.60 (±22.31))

-478.00 (-18.82)

501.0 19.72
175.50 (12.99) Hole 18 (0.71)
B, b ±301.00 (±12.20) ±305.00 (12.01) 77.77 (3.06) Hole 29.5 (1.16)
C, c ±660.00 (±25.98) ±410.00 (±16.14) -9.63 (-0.38) Hole 14.0 (0.55)
D, d ±1270.00 (±20.23) ±410.00 (±16.14) -10.80 (0.43) Hole 12.0 (0.47)
E, e ±2501.0 (±98.46) ±330.0 (±12.99) 234.00 (9.21) Hole 29.5 (1.16)
F, f ±2897.2 (±114.06) ±525.5 (±20.69) 235.0 (9.25) Hole 20.0 (0.79)
G, g ±3248.0 (±127.87)

-551.0 (-21.69)

523.5 (20.61)
233.8 (9.20) Hole 16.0x14.0 (0.63x0.55)
Front

Unit: mm (in)

PointDescription
A, a Hood hinge rear hole 8.0 (0.31)
B, b Hood hinge front hole 8.0 (0.31)
C, c Front strut housing hole 8.0 (0.31)
D, d Hoodledge locator hole 10.0 (0.36)
E, e Upper radiator support top hole 8.0 (0.31)
F, f Upper radiator support front hole 8.0 (0.31)
G, g Bumper reinforcement lower hole 8.0 (0.31)
H, h Lower radiator support hole 8.0 (0.31)
Underbody

MEASUREMENT

The following figure shows a bottom view and a side view of the vehicle.

Unit: mm (in).

Front Left Side of Nissan Murano Vehicle

Dimensions marked with ″*″ indicate symmetrically identical dimensions on both the RH and LH sides of the Nissan Murano vehicle.

MEASUREMENT POINTS

Front

Unit: mm (in)

PointsCoordinatesRemarks
XYZ
A, a ±566.60 (±22.31))

-478.00 (-18.82)

501.0 19.72
175.50 (12.99) Hole 18 (0.71)
B, b ±301.00 (±12.20) ±305.00 (12.01) 77.77 (3.06) Hole 29.5 (1.16)
C, c ±660.00 (±25.98) ±410.00 (±16.14) -9.63 (-0.38) Hole 14.0 (0.55)
D, d ±1270.00 (±20.23) ±410.00 (±16.14) -10.80 (0.43) Hole 12.0 (0.47)
E, e ±2501.0 (±98.46) ±330.0 (±12.99) 234.00 (9.21) Hole 29.5 (1.16)
F, f ±2897.2 (±114.06) ±525.5 (±20.69) 235.0 (9.25) Hole 20.0 (0.79)
G, g ±3248.0 (±127.87)

-551.0 (-21.69)

523.5 (20.61)
233.8 (9.20) Hole 16.0x14.0 (0.63x0.55)
Passenger Compartment

MEASUREMENT

Dimensions marked with ″*″ indicate symmetrically identical dimensions on both the LH and RH side of the Nissan Murano vehicle.

Unit: mm (in)

CoordinatesMeasurementCoordinatesMeasurement
A-D 943.64(37.15) A-C* 1037.90 (40.86)
C-b* 1544.04 (60.79) E-M* 846.53 (33.33)
F-M* 970.77 (38.22) G-S* 1047.83 (41.25)
H-N* 935.61 (36.83) J-P* 1255.09 (49.41)
K-T* 1121.60 (44.16) R-W* 696.45 (27.42)
U-Y* 1072.95 (42.24) Q-X* 790.61 (31.13)
V-Z* 1117.28 (43.99)

MEASUREMENT POINTS

Front
PointDescriptionPointDescription
A Roof flange end of center positioning mark E,e F,f, G,g H,h J,j Front pillar indent
B, b Outer side body joggle M,m, N,n P,p Q,q R,r Center pillar indent
C, c Outer side body indent K,k T,t S,s Door hinge installing hole center
D Center of center cowl top hole V,v W,w X,x Y,y Z,z Rear fender indent
Rear Body

MEASUREMENT

Dimensions marked with ″*″ indicate symmetrically identical dimensions on both the LH and RH side of the Nissan Murano vehicle.

Unit: mm (in)

Front

MEASUREMENT POINTS

Front
PointDescriptionPointDescription
A Roof flange end of center positioning mark B Edge of rear panel between back door striker installing holes
C, c Back pillar main joggle D, d Upper rear panel joggle
Side Radar Bracket

MEASUREMENT

Dimensions marked with ″*″ indicate symmetrically identical dimensions on both the LH and RH side of the Nissan Murano vehicle.

Unit: mm (in)

Front