Removal
REMOVAL
PRECAUTION / NOTICE / HINT
The procedures necessary (adjustment, calibration, initialization or registration), which must be performed once the parts have been removed and reinstalled, or replaced during removal/installation of the main body ECU (multiplex network body ECU), are listed below.
Procedures Required After Replacement / Removal / Installation of PartsReplaced Part or Performed Procedure | Required Procedure | Effect/Inoperative Function When Required Procedure Is Not Performed | Link |
|---|---|---|---|
Disconnect the cable from the negative (-) battery terminal. |
Initialize Back Door Lock |
Door Lock Control System |
|
Memorize Steering Angle Neutral Point |
Lane Departure Alert System (with Steering Control) |
||
Pre-Collision System |
|||
Main body ECU (multiplex network body ECU) |
Perform Code Registration (Immobilizer System) |
|
with Smart Key System: |
PROCEDURE
1. PRECAUTIONS
NOTICE:
After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.
Click here
![]()
2. DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL
NOTICE:
When the cable has been disconnected, some systems must be reset after the cable is reconnected.
Click here
![]()
3. REMOVE NO. 1 INSTRUMENT PANEL LOWER AIRBAG ASSEMBLY
Click here
![]()
4. REMOVE INSTRUMENT PANEL AND NO. 3 CANOPY REINFORCEMENT SUB-ASSEMBLY (except cold area specification vehicles)
Click here
![]()
5. REMOVE INSTRUMENT PANEL AND NO. 3 CANOPY REINFORCEMENT SUB-ASSEMBLY (for cold area specification vehicles)
Click here
![]()
6. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU
(a) Release the latch. |
![]() |
(b) Disconnect the 4 connectors. |
![]() |
(c) Release the claws and pull the lock levers down to disconnect the 2 connectors as shown in the illustration.
![]() |
Remove in this direction |
(d) Remove the bolt and nut. |
![]() |
(e) Release the clip.
(f) Remove the instrument panel junction block assembly with main body ECU.
(g) Release the clip. |
![]() |
(h) Release the clip.
![]() |
Remove in this direction |
(i) Release the claws and pull the lock levers down to disconnect the 2 connectors as shown in the illustration.
(j) Remove the instrument panel junction block assembly with main body ECU.
7. REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
(a) Remove the bolt. |
![]() |
(b) Release the clip to remove the wire harness clamp bracket.
(c) Press the claw of the instrument panel junction block assembly as shown in the illustration to release the lock.
*1 |
Instrument Panel Junction Block Assembly |
*2 |
Main body ECU (multiplex network body ECU) |
![]() |
Push in this direction |
(d) When the lock of the instrument panel junction block assembly is released, insert a screwdriver horizontally, with its tip wrapped in tape, between the main body ECU (multiplex network body ECU) and the instrument panel junction block assembly.
*a |
Protective tape |
![]() |
Insert in this direction |
![]() |
Remove in this direction |
NOTICE:
- Use a screwdriver with a diameter of 5.0 mm (0.197 in.) to 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).
- Do not insert the screwdriver under the connector housing of the main body ECU (multiplex network body ECU).
(e) Using the screwdriver, carefully lift the main body ECU (multiplex network body ECU) to the position where the connector is disconnected.
NOTICE:
Do not twist the screwdriver to lift the main body ECU (multiplex network body ECU).
(f) Lift the main body ECU (multiplex network body ECU) as shown by arrow (1), then pull as shown by arrow (2) in the illustration.
![]() |
Remove in this direction (1) |
![]() |
Remove in this direction (2) |
NOTICE:
Do not touch the connector of the main body ECU (multiplex network body ECU).
.gif)


.png)



.png)
.png)