Rear Suspension

Removal

2steps
~12min
1/5difficulty
Done 0 of 2

REMOVAL

PRECAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed or replaced during removal and installation of the rear suspension member sub-assembly are shown below.

Procedures Required After Replacement / Removal / Installation of Parts

Replaced Part or Performed Procedure

Required Procedure

Effect/Inoperative Function When Required Procedure Is Not Performed

Link

Rear Wheel Alignment Adjustment

  1. Clear the zero point calibration data.
  2. Perform zero point calibration of the yaw rate and acceleration sensor.
  • DTCs are stored
  • ABS warning light comes on
  • Skid control warning light comes on
  • VSC OFF or malfunctioning
  • Rear LH Height Control Sensor Sub-assembly*1
  • Suspension, tires, etc.

    (Vehicle height changes after replacing the suspension or tires)

Initialize Left Headlight ECU Sub-assembly No. 1

Automatic Headlight Leveling System

Exhaust gas leak must be repaired

Verification after Repair

  • Poor idling, etc.
  • Engine start function, etc.
  • *1 with Height Control Sensor

CAUTION:

To avoid burns, do not touch the engine, exhaust pipe or other high-temperature components while the engine is hot.

PROCEDURE

1. REMOVE REAR WHEEL

Click here

2. REMOVE REAR EXHAUST PIPE ASSEMBLY

Click here

3. DISCONNECT REAR LH FLEXIBLE HOSE

(a) Remove the bolt and disconnect the rear LH flexible hose from the flexible hose bracket.

4. DISCONNECT REAR RH FLEXIBLE HOSE

HINT:

Perform the same procedure as for the left side.

5. REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (with Height Control Sensor)

Click here

6. REMOVE REAR STABILIZER LINK ASSEMBLY LH

Click here

7. REMOVE REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the left side.

8. REMOVE REAR STABILIZER BAR

Click here

9. REMOVE REAR COIL SPRING LH

Click here

10. REMOVE REAR COIL SPRING RH

HINT:

Perform the same procedure as for the left side.

11. REMOVE REAR COIL SPRING LOWER SEAT LH

Click here

12. REMOVE REAR COIL SPRING LOWER SEAT RH

HINT:

Perform the same procedure as for the left side.

13. REMOVE REAR SUSPENSION ARM ASSEMBLY NO. 2 LH

Click here

14. REMOVE REAR SUSPENSION ARM ASSEMBLY NO. 2 RH

HINT:

Perform the same procedure as for the left side.

15. REMOVE REAR SUSPENSION ARM ASSEMBLY NO. 1 LH

Click here

16. REMOVE REAR SUSPENSION ARM ASSEMBLY NO. 1 RH

HINT:

Perform the same procedure as for the left side.

17. DISCONNECT REAR UPPER CONTROL ARM ASSEMBLY LH

(a) Remove the bolt and nut, and disconnect the rear LH upper control arm assembly from the rear axle carrier sub-assembly LH.

NOTICE:

Do not turn the nut as it has a stopper. Loosen the bolt with the nut in place.

18. DISCONNECT REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the left side.

19. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

(a) with Height Control Sensor:

(1) Release the clamp to disconnect the height control sensor wire harness.

(b) Using an engine hoist and 4 lifting attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:

  • The rear suspension member sub-assembly is a very heavy component. Make sure it is properly supported.
  • If the rear suspension member sub-assembly is not properly supported, it may fall and cause serious injury.

*a

Engine lifting device

*b

Attachment

Attachment and wooden block locations

(c) Remove the 2 bolts and 2 nuts.

(d) Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.

20. REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Click here

21. REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the left side.

22. REMOVE REAR SUSPENSION MEMBER DAMPER

(a) Remove the 2 bolts and the rear suspension member damper from the rear suspension member sub-assembly.

23. REMOVE REAR SUSPENSION MEMBER HOLE COVER

(a) Remove the 4 rear suspension member hole covers from the rear suspension member sub-assembly as shown in the illustration.

*a

for left side

*b

for right side

24. REMOVE HOLE PLUG

(a) Remove the 7 hole plugs from the rear suspension member sub-assembly as shown in the illustration.