Rear Suspension

Installation

~5min read
0204060801003425N·mlb·ft
Tightening torque found on this page

INSTALLATION

PROCEDURE

1. INSTALL HOLE PLUG

(a) Install the 7 hole plugs to the rear suspension member sub-assembly as shown in the illustration.

2. INSTALL REAR SUSPENSION MEMBER HOLE COVER

(a) Install the 4 rear suspension member hole covers to the rear suspension member sub-assembly.

3. INSTALL REAR SUSPENSION MEMBER STOPPER

(a) Install the rear suspension member stopper to the rear suspension member sub-assembly using the 2 bolts.

Torque:

34 N·m {347 kgf·cm, 25 ft·lbf}

4. INSTALL REAR LEFT UPPER CONTROL ARM ASSEMBLY

Click here

5. INSTALL REAR RIGHT UPPER CONTROL ARM ASSEMBLY

HINT:

Perform the same procedure as for the left side.

6. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

(a) Using an engine lifting device and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

*a

Engine lifting device

*b

Attachment

Attachment and wooden block locations

CAUTION:

  • The rear suspension member sub-assembly is a very heavy component. Make sure it is properly supported.
  • If the rear suspension member sub-assembly is not properly supported, it may fall and cause serious injury.

NOTICE:

  • Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.
  • Keep the rear suspension member sub-assembly supported at all times until installation is complete.

(b) Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and the vehicle.

(c) Install the rear suspension member sub-assembly with the 2 bolts and 2 nuts.

Torque:

143 N·m {1 458 kgf·cm, 105 ft·lbf}

(d) With height control sensor:

(1) Engage the clip to install the height control sensor wire harness.

7. TEMPORARILY INSTALL REAR LEFT UPPER CONTROL ARM ASSEMBLY

(a) Temporarily install the rear left upper control arm assembly to the rear left axle carrier sub-assembly using the bolt and nut.

NOTICE:

  • Insert the bolt with the threaded end facing the rear of the vehicle.
  • Do not turn the nut as it has a stopper. Tighten the bolt with the nut in place.

8. TEMPORARILY INSTALL RIGHT REAR UPPER CONTROL ARM ASSEMBLY

HINT:

Perform the same procedure as for the left side.

9. TEMPORARILY INSTALL REAR SUSPENSION ARM ASSEMBLY NO. 1 LH

Click here

10. TEMPORARILY INSTALL REAR SUSPENSION ARM ASSEMBLY NO. 1 RH

HINT:

Perform the same procedure as for the left side.

11. TEMPORARILY INSTALL REAR SUSPENSION ARM ASSEMBLY NO. 2 LH

Click here

12. TEMPORARILY INSTALL REAR SUSPENSION ARM ASSEMBLY NO. 2 RH

HINT:

Perform the same procedure as for the left side.

13. INSTALL REAR COIL SPRING LOWER SEAT LH

Click here

14. INSTALL REAR COIL SPRING LOWER SEAT RH

HINT:

Perform the same procedure as for the left side.

15. INSTALL REAR COIL SPRING LH

Click here

16. INSTALL REAR COIL SPRING RH

HINT:

Perform the same procedure as for the left side.

17. INSTALL REAR STABILIZER BAR

Click here

18. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (with Height Control Sensor)

Click here

19. CONNECT REAR LH FLEXIBLE HOSE

(a) Connect the rear LH flexible hose to the flexible hose bracket using the bolt.

Torque:

29 N·m {296 kgf·cm, 21 ft·lbf}

20. CONNECT REAR RH FLEXIBLE HOSE

HINT:

Perform the same procedure as for the left side.

21. STABILIZE SUSPENSION

Click here

22. INSTALL REAR STABILIZER LINK ASSEMBLY LH

Click here

23. INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the left side.

24. INSTALL REAR SUSPENSION ARM ASSEMBLY NO. 1 LH

Click here

25. INSTALL REAR SUSPENSION ARM ASSEMBLY NO. 1 RH

HINT:

Perform the same procedure as for the left side.

26. INSTALL REAR SUSPENSION ARM ASSEMBLY NO. 2 LH

(a) Install the No. 2 rear suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.

Torque:

73 N·m {744 kgf·cm, 54 ft·lbf}

NOTICE:

Do not turn the nut as it has a stopper. Tighten the bolt with the nut in place.

27. INSTALL REAR SUSPENSION ARM ASSEMBLY NO. 2 RH

HINT:

Perform the same procedure as for the left side.

28. INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

(a) Install the rear LH upper control arm assembly to the rear axle carrier sub-assembly LH using the bolt.

Torque:

73 N·m {744 kgf·cm, 54 ft·lbf}

NOTICE:

Do not turn the nut as it has a stopper. Tighten the bolt with the nut in place.

29. INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the left side.

30. INSTALL REAR EXHAUST PIPE ASSEMBLY

Click here

31. INSTALL REAR WHEEL

Click here

32. INSTALL REAR SUSPENSION ARM ASSEMBLY NO. 2 LH

(a) Install the rear suspension arm assembly No. 2 LH (rear suspension member sub-assembly side) using the nut.

Click here

33. INSTALL REAR SUSPENSION ARM ASSEMBLY NO. 2 RH

HINT:

Perform the same procedure as for the left side.

34. CHECK FOR EXHAUST GAS LEAKS

Click here

35. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Click here

36. PERFORM INITIALIZATION (with Height Control Sensor)

Click here