Front Suspension

Removal

2steps
~47min
5/5difficulty
7special tools
Done 0 of 2

REMOVAL

PRECAUTION / NOTICE / HINT

The procedures required after the parts are removed and installed or replaced during removal/installation of the front shock absorber assembly (adjustment, calibration, initialization or registration) are shown below.

Procedures Required After Replacement / Removal / Installation of Parts

Replaced Part or Performed Procedure

Required Procedure

Effect/Inoperative Function When Required Procedure Is Not Performed

Link

Front wheel alignment adjustment

  1. Clear the zero point calibration data.
  2. Perform zero point calibration of the yaw rate and acceleration sensor.
  • DTCs are stored
  • ABS warning light comes on
  • Skid control warning light comes on
  • VSC OFF or malfunctioning

Suspension, tires, etc.

(Vehicle height changes after replacing the suspension or tires)

Initialize Left Headlight ECU Sub-assembly No. 1

Automatic Headlight Leveling System

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.

PROCEDURE

1. REMOVE FRONT WHEEL

Click here

2. REMOVE FRONT WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Click here

3. REMOVE NO. 1 HEATER DUCT SPLASH SHIELD SEAL

(a) Release the clip to remove the No. 1 heater duct splash shield seal from the cowl top panel outer subassembly.

4. REMOVE LEFT WATERPROOF COVER PLATE

(a) Release the clip to remove the left waterproof cover plate.

5. REMOVE LEFT COWL BODY MOUNTING BRACKET

(a) Remove the bolt and left cowl body mounting bracket from the vehicle body.

6. REMOVE RIGHT COWL BODY MOUNTING BRACKET

(a) Remove the 2 bolts and right cowl body mounting bracket from the vehicle body.

7. REMOVE COWL TOP PANEL OUTER SUBASSEMBLY

(a) with windshield defogger:

(1) Disconnect the connector.

(2) Release the 2 clips to detach the wire harness from the cowl top panel outer subassembly.

(b) Release the 2 clips to detach the wire harness from the cowl top panel outer subassembly.

(c) Remove the 8 bolts, 4 nuts and cowl top panel outer subassembly.

8. REMOVE FRONT SUSPENSION SUPPORT DUST COVER

(a) Remove the front suspension support dust cover from the front shock absorber assembly.

9. LOOSEN NUT BETWEEN FRONT SUPPORT AND FRONT SHOCK ABSORBER

(a) Temporarily install the 2 nuts on the front shock absorber assembly.

(b) Loosen the nut from the front shock absorber assembly.

CAUTION:

  • Only loosen the nut between the front support and front shock absorber when the front shock absorber with coil spring must be removed.
  • Only loosen the nut between the front support and front shock absorber; do not remove it.
  • If the nut between the front support and front shock absorber is removed while the front coil spring is compressed, the components of the shock absorber with coil spring may be ejected.

10. DISCONNECT FRONT STABILIZER BAR LINK ASSEMBLY

(a) Remove the nut to detach the front stabilizer bar link assembly from the front shock absorber assembly.

NOTICE:

Be careful not to damage the ball joint boot.

HINT:

If the ball joint turns together with the nut, hold the stud with a 6 mm hexagon socket wrench.

11. DISCONNECT FRONT SPEED SENSOR

(a) Release the latch.

(b) Remove the bolt.

(c) Release the 2 hooks to detach the front speed sensor and front hose from the front shock absorber assembly.

NOTICE:

Make sure to fully detach the front speed sensor and front hose from the front shock absorber assembly.

12. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

(a) Support the front suspension arm No. 1 lower subassembly with a jack and wooden block.

*a

Wooden Block

*b

Jack

Front of Vehicle

Wooden Block Location

NOTICE:

Support the front suspension arm lower subassembly No. 1 until installation of the front shock absorber with coil spring is complete.

(b) Remove the 2 bolts and 2 nuts, then detach the front shock absorber with coil spring (lower side) from the steering knuckle.

NOTICE:

  • When removing the nuts, prevent the bolts from turning.
  • Use wire or an equivalent tool to suspend the separated steering knuckle.

(c) Remove the 3 nuts, 2 spacers and front shock absorber with coil spring.

13. REMOVE NUT BETWEEN FRONT SUPPORT AND FRONT SHOCK ABSORBER

(a) Secure the SST in a vise.

SST: 09727-00051

SST: 09727-30022

09727-00010

09727-00031

(b) Attach the hooks of each SST arm to the coil spring.

CAUTION:

  • Make sure the hooks are properly attached to the coil spring.
  • If a hook comes off the coil spring, the coil spring may be ejected and cause injury.
  • Make sure the hooks of the upper and lower SST arms are attached to the coil spring so that the distance between the hooks is as large as possible.
  • If a hook comes off the coil spring, the coil spring may be ejected and cause injury.
  • Make sure the SST arms are parallel and the number of coils between the arms is the same on each side.
  • If a hook comes off the coil spring, the coil spring may be ejected and cause injury.

(c) Install the stopper pins on the SST hooks.

CAUTION:

  • Make sure the stopper pins are properly installed.
  • If a hook comes off the coil spring, the coil spring may be ejected and cause injury.

(d) Reinstall the SST and the 2 vehicle nuts on the upper support, as shown in the illustration.

SST: 09727-30022

09727-00090

09727-00100

*a

Vehicle nut

(e) Using the SST, compress the coil spring.

CAUTION:

  • If the coil spring starts to come loose while using the SST, stop immediately and properly reattach the SST.
  • If a hook comes off the coil spring, the coil spring may be ejected and cause injury.
  • Do not compress the coil spring until the coils contact each other.
  • If a hook comes off the coil spring, the coil spring may be ejected and cause injury.
  • Do not use an impact wrench.
  • If an impact wrench is used, the SST threads may be damaged, or sudden compression of the coil spring could cause a hook to come off the coil spring, be ejected and cause injury.
  • If a stopper pin contacts the coil spring while using the SST, remove the stopper pin and continue the procedure.
  • If a stopper pin is removed, install a coil spring stopper strap as shown in the illustration.
  • If a hook comes off the coil spring, the coil spring may be ejected and cause injury.

SST: 09727-00110

(f) Check that the coil spring is disengaged, then remove the front support from the front shock absorber nut.

CAUTION:

  • Do not remove the front support from the front shock absorber nut while the coil spring is compressed.
  • If the nut between the front support and front shock absorber is removed while the front coil spring is compressed, the front shock absorber with coil spring components may be ejected and cause injury.

14. REMOVE COLLAR

(a) Remove the collar from the front shock absorber assembly.

15. REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

(a) Remove the front suspension support sub-assembly from the front shock absorber assembly.

16. REMOVE FRONT SPRING SEAT SUB-ASSEMBLY WITH BEARING

(a) Release the front spring seat sub-assembly with insulator from the claws of the front shock absorber assembly.

*1

Front spring seat sub-assembly with insulator

*a

Claw

(b) Remove the front spring seat sub-assembly with insulator from the front shock absorber assembly.

17. REMOVE FRONT COIL SPRING

(a) Remove the front coil spring and the SST.

NOTICE:

Do not use an impact wrench. This would damage the SST.

18. REMOVE FRONT SPRING UPPER SEAT

(a) Remove the front spring upper seat from the front shock absorber assembly, as shown in the illustration.

Remove in this direction

19. REMOVE FRONT COIL SPRING LOWER INSULATOR

(a) Remove the front coil spring lower insulator from the front shock absorber assembly.

20. REMOVE FRONT SHOCK ABSORBER ASSEMBLY