Installation
INSTALLATION
PRECAUTION / NOTICE / HINT
HINT:
- Repeat the same procedure for the right side and the left side.
- The following procedure applies to the left side.
PROCEDURE
1. INSTALL FRONT COIL SPRING LOWER INSULATOR
(a) Install the front coil spring lower insulator to the front shock absorber assembly.
![]() |
Positioning pin |
NOTICE:
When installing the front coil spring lower insulator, insert the spring seat positioning pin into the hole of the front coil spring lower insulator.
2. INSTALL FRONT SPRING UPPER SEAT
(a) Install the front spring upper seat to the front shock absorber assembly, as shown in the illustration.
![]() |
Install in this direction |
NOTICE:
- Point the coil of the front spring upper seat with the smallest diameter downward.
- Do not apply lubricant to the front spring upper seat.
- Do not apply lubricant to the cap or rod of the front shock absorber assembly.
- Do not clean the front spring upper seat with water or solvent.
3. INSTALL FRONT COIL SPRING
(a) Secure the SST in a vise. SST: 09727-00051 SST: 09727-30022 09727-00010 09727-00031 |
![]() |
(b) Attach the hooks of each SST arm to the coil spring.
CAUTION:
- Make sure the hooks are properly attached to the coil spring.
.png)
- If a hook comes off the coil spring, the coil spring may be ejected and cause injury.
- Make sure the hooks of the upper and lower SST arms are attached to the coil spring so that the distance between the hooks is as large as possible.
.png)
- If a hook comes off the coil spring, the coil spring may be ejected and cause injury.
- Make sure the SST arms are parallel and the number of coils between the arms is the same on each side.
.png)
- If a hook comes off the coil spring, the coil spring may be ejected and cause injury.
(c) Install the stopper pins on the SST hooks.
CAUTION:
- Make sure the stopper pins are properly installed.
- If a hook comes off the coil spring, the coil spring may be ejected and cause injury.
(d) Using the SST, compress the coil spring.
CAUTION:
- If the coil spring starts to come loose while using the SST, stop immediately and properly reattach the SST.
.png)
- If a hook comes off the coil spring, the coil spring may be ejected and cause injury.
- Do not compress the coil spring until the coils contact each other.
.png)
- If a hook comes off the coil spring, the coil spring may be ejected and cause injury.
- Do not use an impact wrench.
.png)
- If an impact wrench is used, the SST threads may be damaged, or sudden compression of the coil spring could cause a hook to come off the coil spring, be ejected and cause injury.
- If a stopper pin contacts the coil spring while using the SST, remove the stopper pin and continue the procedure.

- If a stopper pin is removed, install a coil spring stopper strap as shown in the illustration.
- If a hook comes off the coil spring, the coil spring may be ejected and cause injury.
SST: 09727-00110
(e) Align the end of the front coil spring with the flange of the front coil spring lower insulator, and install the front coil spring. NOTICE: Make sure the end of the front coil spring with the largest diameter is positioned in the recess of the front coil spring lower insulator. |
|
4. INSTALL FRONT SPRING SEAT SUB-ASSEMBLY WITH BEARING
(a) Install the front spring seat sub-assembly with insulator to the front shock absorber assembly. NOTICE: Make sure the upper end of the bearing (shock absorber dust cover) and the spacer mount bearing are properly seated. |
|
5. INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY
(a) Install the front suspension support sub-assembly as shown in the illustration.
*a |
Cutout |
![]() |
Outside the Vehicle |
NOTICE:
Make sure the cutout of the piston rod and the cutout of the front suspension support sub-assembly are aligned.
(b) Align the protrusion of the front suspension support sub-assembly with the front shock absorber lower support as shown in the illustration.
*a |
0°+/- 5° |
*b |
Front suspension support sub-assembly guide line |
*c |
Area where the protrusions must be aligned |
*d |
Front suspension support sub-assembly protrusion |
*e |
Front shock absorber lower support |
*f |
Upper housing protrusion |
*g |
Lower housing protrusion |
![]() |
Outside the Vehicle |
NOTICE:
Be sure to install the front suspension support sub-assembly so that the protrusion of the front suspension support sub-assembly is aligned within +/- 5° of the center of the front shock absorber lower support.
(c) Align the upper housing and lower housing protrusions of the mount bearing, as shown in the illustration.
NOTICE:
Be sure to install the front spring seat sub-assembly with insulator so that the upper housing protrusion of the mount bearing covers the lower housing protrusion within the guide lines of the front suspension support sub-assembly.
6. INSTALL COLLAR
(a) Install the collar to the front shock absorber assembly.
7. TEMPORARILY TIGHTEN NUT BETWEEN FRONT SUPPORT AND FRONT SHOCK ABSORBER
(a) Temporarily tighten a new nut between the front support and the front shock absorber.
(b) Remove the SST from the front coil spring.
NOTICE:
Do not use an impact wrench. This would damage the SST.
8. CONNECT FRONT SPRING SEAT SUB-ASSEMBLY WITH BEARING
(a) Engage the end of the front spring seat sub-assembly with bearing with the claws of the front shock absorber. NOTICE:
|
|
9. INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING
(a) Install the front shock absorber with coil spring (upper side) using the nut and 2 spacers. Torque: 50 N·m {510 kgf·cm, 37 ft·lbf} |
![]() |
(b) Temporarily install the 2 nuts on the front shock absorber assembly. |
![]() |
(c) Install the front shock absorber with coil spring (lower side) on the steering knuckle using the 2 bolts and 2 nuts.
Torque:
270 N·m {2 753 kgf·cm, 199 ft·lbf}
NOTICE:
- When installing the nuts, prevent the bolts from turning.
- Do not apply lubricant to the contact surfaces of the steering knuckle and shock absorber.
HINT:
The bolts can be installed in either direction. However, make sure both bolts are installed in the same direction.
10. INSTALL FRONT SPEED SENSOR
(a) Engage the 2 claws of the front speed sensor with the front shock absorber assembly. NOTICE: Do not twist the front speed sensor when installing it. |
![]() |
(b) Install the front speed sensor and front hose on the front shock absorber assembly using the bolt. Torque: 29 N·m {296 kgf·cm, 21 ft·lbf} |
![]() |
(c) Engage the clip.
11. INSTALL FRONT STABILIZER LINK ASSEMBLY
(a) Install the front stabilizer link assembly on the front shock absorber assembly with the nut.
Torque:
74 N·m {755 kgf·cm, 55 ft·lbf}
HINT:
If the ball joint turns together with the nut, hold the stud with a 6 mm hexagon socket wrench.
12. FULLY TIGHTEN NUT BETWEEN FRONT SUPPORT AND FRONT SHOCK ABSORBER
(a) Fully tighten the nut between the front support and front shock absorber.
Torque:
47 N·m {479 kgf·cm, 35 ft·lbf}
NOTICE:
Perform this step only when the front shock absorber with coil spring has been removed.
(b) Remove the 2 nuts from the front shock absorber assembly. |
![]() |
13. INSTALL FRONT SUSPENSION SUPPORT DUST COVER
(a) Install the front suspension support dust cover.
14. INSTALL FENDER APRON UPPER OUTER PANEL SUB-ASSEMBLY
(a) Install the fender apron upper outer panel sub-assembly with the 8 bolts and 4 nuts.
Torque:
Bolt:
12 N·m {122 kgf·cm, 9 ft·lbf}
Nut:
50 N·m {510 kgf·cm, 37 ft·lbf}
(b) Engage the 2 clips to install the wire harness on the fender apron upper outer panel sub-assembly.
(c) With windshield defroster:
(1) Engage the 2 clips to install the wire harness on the fender apron upper outer panel sub-assembly.
(2) Connect the connector.
15. INSTALL RIGHT FENDER APRON BRACKET REINFORCEMENT
(a) Install the right fender apron bracket reinforcement on the vehicle body using the 2 bolts.
Torque:
12 N·m {122 kgf·cm, 9 ft·lbf}
16. INSTALL LEFT FENDER APRON BRACKET REINFORCEMENT
(a) Install the left fender apron bracket reinforcement on the vehicle body using the bolt.
Torque:
12 N·m {122 kgf·cm, 9 ft·lbf}
17. INSTALL LEFT WATERPROOF PROTECTIVE PLATE
(a) Engage the claw to install the left waterproof protective plate on the fender apron upper outer panel sub-assembly.
18. INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
(a) Engage the claw to install the No. 1 heater air duct splash shield seal on the fender apron upper outer panel sub-assembly.
19. INSTALL FRONT WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Click here![]()
20. INSTALL FRONT WHEEL
Click here
![]()
21. STABILIZE SUSPENSION
(a) Lower the vehicle.
(b) Bounce the vehicle up and down several times to stabilize the suspension.
22. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
Click here![]()
23. PERFORM INITIALIZATION (with height control sensor)
Click here![]()
.png)
.png)
.png)





.png)
.png)