Installation
INSTALLATION
PRECAUTION / NOTICE / HINT
NOTICE:
- Always use a new grommet, washer and valve core when installing the tire pressure warning valve and transmitter.
- Make sure the washer and nut are not damaged, and replace them if necessary.
- Do not damage the urethane coating on the back of the tire pressure warning valve and transmitter assembly (surface opposite the side with the ID code) with a sharp object.
- Record the ID number before installation.
- Make sure there is no oil, water or lubricant on the wheel rim hole, tire pressure warning valve, washer or nut. Failure to follow this instruction may result in incorrect installation.
- Use only a specified tire valve cap. If a tire valve cap that does not meet specifications is used, it may seize to the tire pressure warning valve and transmitter.
PROCEDURE
1. INSTALL TIRE PRESSURE WARNING VALVE AND TRANSMITTER
(a) Install a new grommet onto the tire pressure warning valve and transmitter.
NOTICE:
A new tire pressure warning valve and transmitter are supplied with a grommet already installed. Do not install an additional grommet.
(b) Record the 7-digit transmitter ID number shown in the illustration. |
|
(c) Insert the tire pressure warning valve and transmitter with the grommet from the inside of the wheel rim.
NOTICE:
- Make sure the tire pressure warning valve and transmitter are installed so that the printed surface is visible. If they are installed in the opposite direction, the tire pressure warning valve and transmitter may be damaged, or signal transmission may fail when the vehicle is driven at high speed.
- Make sure there is no deformation or damage to the tire pressure warning valve and transmitter.
- Make sure there are no foreign objects on the grommet or around the wheel rim hole.
(d) Install the washer onto the tire pressure warning valve and transmitter from the outside of the wheel rim, then using an 11 mm long socket wrench, tighten the nut. Torque: 4 N·m {41 kgf·cm, 35 in·lbf} NOTICE:
|
|
(e) Place the tire and wheel rim on the tire mounting machine, as shown in the illustration.
*a |
Tire mounting machine clamp tool |
*b |
60° |
*c |
Wheel rim |
![]() |
Wheel rim rotation direction |
![]() |
Tire pressure warning valve and transmitter area |
NOTICE:
- Position the main body of the tire pressure warning valve and transmitter in the area shown in the illustration.
- If the tire pressure warning valve and transmitter are placed outside this area, they will contact the tire bead and may be damaged.
(f) Apply a sufficient amount of soapy water or an equivalent product to the wheel rim and tire bead.
NOTICE:
Do not apply soapy water or an equivalent product directly onto the tire pressure warning valve and transmitter.
(g) Using a tire mounting machine, install the tire onto the wheel rim.
NOTICE:
- Make sure the tire bead and the mounting tool do not obstruct the tire pressure warning valve and transmitter.
- Make sure the tire pressure warning valve and transmitter are not pinched between the wheel rim and the tire bead.
(h) Install a new valve core.
(i) Inflate the tire to the specified tire inflation pressure.
Click here
![]()
(j) The nut may be loosened after the tire is inflated. Using an 11 mm long socket wrench, tighten the nut to the specified torque.
Torque:
4 N·m {41 kgf·cm, 35 in·lbf}
NOTICE:
No additional tightening is required once the nut is tightened to the specified torque.
(k) Check for air leaks around the tire pressure warning valve and transmitter using soapy water or an equivalent product.
(1) If the valve core leaks air, press the valve core several times to remove foreign matter. Replace the valve core if necessary.
(2) If air leaks from the tire pressure warning valve and transmitter, check whether the grommet, washer and nut are deformed, damaged or obstructed by foreign matter. Replace the grommet, washer or nut if necessary.
(l) Install the tire valve cap.
2. INSTALL WHEEL ASSEMBLY
Click here
![]()
3. INSPECT TIRES
Click here
![]()
4. REGISTER TRANSMITTER ID
Click here![]()
5. INSPECT TIRE PRESSURE WARNING SYSTEM
Click here![]()
6. PERFORM INITIALIZATION
Click here![]()


.png)
.png)