Toyota Camry Quiz
Front suspension

Front suspension arm sub-assy lower No.1 LH

In this manual: Front suspension
Introduction — 61Audio & visual system — 16Automatic transmission / trans — 19Transmission revolution (ATM) — 1Shift lock system (ATM) — 1Brake — 20Clutch — 10Communication system — 4Cooling — 15Cruise control — 3Drive shaft / propeller shaft — 9Emission control — 8Engine control system — 12Engine hood/door — 7Exhaust — 3Exterior/interior trim — 14Front suspension — 9Fuel — 12Heater & air conditioner — 16Ignition — 8Instrument panel/meter — 7Intake — 7Lighting — 11Lubrication — 16Manual transmission/transaxle — 13Parking brake — 10Power steering — 7Rear suspension — 10Seat — 12Service specifications — 26Sliding roof/convertible — 4Starting & charging — 11Starting system (2AZ−FE)(From July, 2003) — 1Starting system (1MZ−FE/3MZ−FE) — 1Steering column — 6Theft deterrent & door lock — 9Tire & wheel — 4Windshield/windowglass/mirror — 5Back window glass — 1Power window control system — 1Power mirror control system — 1Inner rear view mirror assy — 1Windshield glass — 1Wiring — 1
16steps
~96min
4/5difficulty
060120180240300200148N·mlb·ft
Tightening torque found on this page
Done 0 of 16
REPLACEMENT

HINT:

COMPONENTS

  1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (1MZ−FE ENGINE TYPE)
  2. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (2AZ−FE ENGINE TYPE)
  3. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (3MZ−FE ENGINE TYPE)
  4. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR (A/T TRANSAXLE)

a. Remove the 3 nuts and the transverse engine engine mounting insulator.

Remove transverse engine engine mounting insulator (A/T transaxle) Remove transverse engine engine mounting insulator (A/T transaxle) 5. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR (M/T TRANSAXLE)
  1. Remove the 3 nuts and the transverse engine engine mounting insulator.
  2. Remove the 4 bolts and bracket from the manual transmission.
6. REMOVE FRONT SUSPENSION ARM SUB−ASSY LOWER No.1 LH

a. Remove the 2 bolts on the front side of the front suspension arm sub−assy lower No. 1 LH.

  1. Remove the bolt and nut on the rear side of the front suspension arm sub−assy lower No. 1 LH.
  2. Remove the front suspension arm sub−assy lower No. 1 LH.
  3. Remove the front lower arm bush stopper from the front suspension arm sub−assy lower No. 1 LH.
    7. INSTALL FRONT SUSPENSION ARM SUB−ASSY
7. INSTALL FRONT SUSPENSION ARM SUB−ASSY LOWER No.1 LH
  1. Install the front lower arm bush stopper to the front suspension arm sub−assy lower No. 1 LH.
  2. Install the front suspension arm sub−assy lower No. 1 LH with the 2 bolts to the front side. Torque: 200 N·m
    c. Install the front suspension arm sub−assy lower No. 1 LH
c. Install the front suspension arm sub−assy lower No. 1 LH with the bolt and nut to the rear side.Torque: 206 N·m
8. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING
8. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR (A/T TRANSAXLE) a. Install the transverse engine engine mounting insulator with the 3 nuts.Torque: 87 N·m
9. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR (M/T TRANSAXLE)
9. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR (M/T TRANSAXLE)
  1. Install the bracket with the 4 bolts to the manual transmission. Torque: 64 N·m
  2. Install the transverse engine engine mounting insulator with the 3 nuts. Torque: 87 N·m
  3. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (2AZ−FE ENGINE TYPE)
  4. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (1MZ−FE ENGINE TYPE)
  5. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (3MZ−FE ENGINE TYPE)

Test yourself

A quick Toyota Camry quiz: every answer comes with an explanation and a link to the manual page.