Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
84540 |
- |
- |
|
2 |
TRANSMISSION CONTROL CABLE ASSEMBLY |
33820B |
- |
- |
|
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
3 |
BATTERY CLAMP SUB-ASSEMBLY |
74404A |
- |
- |
- |
4 |
ECM |
89661 |
- |
- |
- |
5 |
AUXILIARY BATTERY |
- |
- |
- |
- |
6 |
INSPECT SHIFT LEVER POSITION |
- |
- |
- |
|
7 |
ADJUST SHIFT LEVER POSITION |
- |
- |
- |
|
8 |
INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
- |
- |
- |
|
9 |
ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
- |
- |
- |
|
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
PROCEDURE
1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
*a |
N |
*b |
Protrusion |
(1) Temporarily install the park/neutral position switch assembly to the transaxle case sub-assembly with the 2 bolts.
(2) Temporarily install the transmission control shaft lever to the manual valve lever shaft.
(3) Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.
NOTICE:
If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.
*1 |
Transmission Control Shaft Lever |
*a |
Manual Valve Link Lever Sub-assembly |
*b |
Manual Valve |
(4) Remove the transmission control shaft lever from the manual valve lever shaft.
(5) Align the protrusions of the park/neutral position switch assembly as shown in the illustration.
(6) Hold the park/neutral position switch assembly in that position and tighten the 2 bolts.
Torque:
5,4 N·m {55 kgf·cm, 48 in·lbf}
(7) Install the transmission control shaft lever to the manual valve lever shaft with the washer and nut.
Torque:
12,7 N·m {130 kgf·cm, 9 ft·lbf}
NOTICE:
Be careful of the direction of the transmission control shaft lever.
(8) Connect the park/neutral position switch connector.
2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
![]() |
NOTICE: Before connecting the transmission control cable assembly, check that the shift lever is in N. |
*a |
N |
*b |
Correct |
*c |
Incorrect |
- |
- |
(1) Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.
NOTICE:
If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.
*1 |
Transmission Control Shaft Lever |
*a |
Manual Valve Link Lever Sub-assembly |
*b |
Manual Valve |
(2) Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
(3) Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.
3. INSTALL BATTERY CLAMP SUB-ASSEMBLY
Click here ![]()
4. INSTALL ECM
Click here
![]()
5. INSTALL AUXILIARY BATTERY
Click here
![]()
6. INSPECT SHIFT LEVER POSITION
Click here ![]()
7. ADJUST SHIFT LEVER POSITION
Click here ![]()
8. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Click here ![]()
9. ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Click here
![]()
.png)
.png)
.png)
.gif)
.png)
.png)