Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
CAMSHAFT POSITION SENSOR (for Exhaust Side) |
11102A |
- |
- |
|
2 |
CAMSHAFT POSITION SENSOR (for Intake Side) |
11102A |
- |
- |
|
3 |
ENGINE OIL LEAK |
- |
- |
- |
|
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
★ |
Precoated part |
- |
- |
NOTICE:
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here ![]()
PROCEDURE
1. INSTALL CAMSHAFT POSITION SENSOR (for Exhaust Side)
*1 |
O-ring |
- |
- |
*a |
Seam |
*b |
Camshaft Position Sensor Tip |
*c |
OK |
*d |
NG |
(1) Perform this procedure only when reusing the camshaft position sensor.
1. Clean the O-ring groove of the camshaft position sensor.
NOTICE:
Make sure the O-ring groove is free of foreign matter.
2. Install a new O-ring to the camshaft position sensor.
NOTICE:
Set the O-ring on the tip of the camshaft position sensor and roll it into the O-ring groove with bare hands to install it.
3. Check if the O-ring is twisted.
HINT:
Check the entire circumference of the seam of the O-ring for twisting.
(2) Apply a light coat of engine oil to the O-ring of the camshaft position sensor.
NOTICE:
If reusing the camshaft position sensor, be sure to inspect the O-ring.
(3) Using an 8 mm socket wrench, install the camshaft position sensor to the cylinder head cover sub-assembly with a new bolt.
Torque:
7,5 N·m {76 kgf·cm, 66 in·lbf}
NOTICE:
- If the camshaft position sensor has been struck or dropped, replace it.
- Make sure that the O-ring is not cracked or moved out of place when installing the camshaft position sensor.
(4) Connect the camshaft position sensor connector.
2. INSTALL CAMSHAFT POSITION SENSOR (for Intake Side)
*1 |
O-ring |
- |
- |
*a |
Seam |
*b |
Camshaft Position Sensor Tip |
*c |
OK |
*d |
NG |
(1) Perform this procedure only when reusing the camshaft position sensor.
1. Clean the O-ring groove of the camshaft position sensor.
NOTICE:
Make sure the O-ring groove is free of foreign matter.
2. Install a new O-ring to the camshaft position sensor.
NOTICE:
Set the O-ring on the tip of the camshaft position sensor and roll it into the O-ring groove with bare hands to install it.
3. Check if the O-ring is twisted.
HINT:
Check the entire circumference of the seam of the O-ring for twisting.
(2) Apply a light coat of engine oil to the O-ring of the camshaft position sensor.
NOTICE:
If reusing the camshaft position sensor, be sure to inspect the O-ring.
(3) Using an 8 mm socket wrench, install the camshaft position sensor to the cylinder head cover sub-assembly with a new bolt.
Torque:
7,5 N·m {76 kgf·cm, 66 in·lbf}
NOTICE:
- If the camshaft position sensor has been struck or dropped, replace it.
- Make sure that the O-ring is not cracked or moved out of place when installing the camshaft position sensor.
(4) Connect the camshaft position sensor connector.
3. INSPECT FOR ENGINE OIL LEAK
![]() |
Click here |
.png)
.png)
.png)
.gif)
.png)