Suspension

Installation

~3min read
03060901201507354N·mlb·ft
Tightening torque found on this page

INSTALLATION

Procedure

Part Name Code

1

TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

48720A

-

-

2

TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

48740F

-

-

3

REAR LOWER COIL SPRING INSULATOR

48259A

-

-

-

4

REAR COIL SPRING

48231B

-

-

5

STABILIZE SUSPENSION

-

-

-

6

REAR STABILIZER LINK ASSEMBLY

48840A

-

-

7

FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

48720A

-

-

8

FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

48740F

-

-

9

REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

89408C

-

-

-

10

REAR WHEEL

-

-

-

-

11

FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

48740F

-

-

12

INSPECT AND ADJUST REAR WHEEL ALIGNMENT

-

-

-

13

PERFORM CALIBRATION

-

-

-

*A

for Gasoline Model

*B

for HEV Model

*C

for LH Side

*D

w/ Parking Assist Monitor System

*1

REAR SUSPENSION TOE ADJUST CAM SUB-ASSEMBLY

*2

NO. 2 CAMBER ADJUST CAM

*3

CAP

*4

REAR STABILIZER BAR

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)

-

-

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

NOTICE:

  • Tighten the bolt with the nut secured.
  • Insert the bolt with the threaded end facing the front of the vehicle.

2. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

NOTICE:

  • Insert the rear suspension toe adjust cam sub-assembly from the rear of the vehicle.
  • When tightening the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.

3. INSTALL REAR LOWER COIL SPRING INSULATOR

4. INSTALL REAR COIL SPRING

Click here

5. STABILIZE SUSPENSION

Click here

6. INSTALL REAR STABILIZER LINK ASSEMBLY

Click here

7. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

NOTICE:

Tighten the bolt with the nut secured.

Torque:

73 N·m {744 kgf·cm, 54 ft·lbf}

8. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

NOTICE:

Tighten the bolt with the nut secured.

Torque:

for Rear Axle Carrier Sub-assembly Side :

73 N·m {744 kgf·cm, 54 ft·lbf}

9. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

for LH Side:

Click here

10. INSTALL REAR WHEEL

Click here

11. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

(a) for Rear Suspension Member Sub-assembly Side:

*A

for HEV Model

*B

for Gasoline Model

*a

Matchmark

-

-

(1) Lower the vehicle to the ground.

(2) Bounce the vehicle up and down at the corners to stabilize the rear suspension.

(3) Align the matchmarks on the No. 2 camber adjust cam, rear suspension toe adjust cam sub-assembly and rear suspension member sub-assembly.

(4) Fully tighten the nut.

Torque:

100 N·m {1020 kgf·cm, 74 ft·lbf}

NOTICE:

  • Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.
  • Make sure that the vehicle is unloaded when fully tightening the nut.

12. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Click here

13. PERFORM CALIBRATION (w/ Parking Assist Monitor System)

Parking assist monitor system

Automatic headlight beam level control system