Inverter "A" Cooling System Performance (P0A9300)
DTC SUMMARY
MALFUNCTION DESCRIPTION
This DTC indicates when the temperature sensor value inside the inverter has become abnormal. The cause of this malfunction may be one of the following:
Internal inverter malfunction- Inverter internal circuit malfunction
- Malfunction in ECU that controls the inverter
- Malfunction in sensor for inverter control (coolant temperature sensor)
- Coolant is leaking, coolant level is insufficient, coolant is frozen or coolant passage is clogged.
- Grille is blocked.
DESCRIPTION
Refer to the system description for the Cooling System.
Click here ![]()
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | Note |
|---|---|---|---|---|---|---|
P0A9300 |
Inverter "A" Cooling System Performance |
(1 trip detection logic) |
|
Comes on |
Master Warning: Comes on |
SAE Code: P0A93 |
MONITOR DESCRIPTION
If the hybrid vehicle control ECU detects a malfunction of the inverter cooling system, the ECU will illuminate the MIL and store a DTC.
MONITOR STRATEGY
Related DTCs |
P0A93 (INF P0A9300): HV cooling system malfunction |
Required sensors/components |
Water pump, radiator fan, inverter, boost converter |
Frequency of operation |
Continuous |
Duration |
TMC's intellectual property |
MIL operation |
1 driving cycle |
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
Hybrid vehicle control ECU |
DTC P0A93 (INF P0A9300) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
.gif)
- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
.gif)
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON and turn the GTS on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for 2 minutes or more.
- Turn the ignition switch to ON and turn the GTS on.
- With ignition switch ON and wait for 5 seconds or more. [*1]
- Turn the ignition switch to ON (READY) and wait for 5 seconds or more. [*2]
- Perform a road test according to the freeze frame data item "Vehicle Speed" for approximately 10 minutes. [*3]
NOTICE:
As the state of charge of the HV battery voltage may be low after driving in fail-safe mode, it will automatically be charged for 5 to 10 minutes after repairs have been performed and turn the ignition switch to ON (READY).
HINT:
[*1] to [*3] : Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.
WIRING DIAGRAM
Refer to the wiring diagram for Cooling System.
Click here ![]()
CAUTION:
Refer to the precautions before inspecting high voltage circuit.
Click here ![]()
NOTICE:
- After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
.gif)
- When disconnecting and reconnecting the auxiliary battery
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
.gif)
HINT:
- P0A9300 may be output as a result of the malfunction indicated by the DTCs in table below.
- The chart above is listed in inspection order of priority.
- Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Malfunction Content | System | Relevant DTC |
|
|---|---|---|---|
Insulation malfunction |
Hybrid Control System |
P1C7C49 |
Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure |
P1C7D49 |
Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure |
||
P1C7E49 |
Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure |
||
P1C7F49 |
Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure |
||
P1C8049 |
Hybrid/EV Battery Voltage System Isolation (Rear Motor Area) Internal Electronic Failure |
||
Malfunction Content | System | Relevant DTC |
|
|---|---|---|---|
Sensor and actuator circuit malfunction |
Hybrid Control System |
P0C7396 |
Motor Electronics Coolant Pump "A" Component Internal Failure |
P314A31 |
Motor Electronics Coolant Pump "A" No Signal |
||
Motor Generator Control System |
P0A0011 |
Motor Electronics Coolant Temperature Sensor Circuit Short to Ground |
|
P0A0015 |
Motor Electronics Coolant Temperature Sensor Circuit Short to Battery or Open |
||
PROCEDURE
CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)
Click here ![]()
Result | Proceed to |
|---|---|
OK |
A |
NG (The connector is not connected securely.) |
B |
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) |
C |
| B | CONNECT SECURELY |
| C | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK COOLING SYSTEM
Click here ![]()
HINT:
If the "Cooling System" inspection results are normal, perform the next step.
| NEXT | REPLACE HV COOLANT |