Neutral Position Switch Circuit
DESCRIPTION
The engine stop and start ECU uses the park/neutral position switch assembly installed to the continuously variable transaxle assembly to detect when the shift lever is in P or N.
WIRING DIAGRAM
Refer to DTC P085012.
Click here
![]()
NOTICE:
- Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.
Click here
.gif)
- After replacing the engine stop and start ECU, perform learning of the external backup boost converter (eco run vehicle converter assembly).
Click here
.gif)
- After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click here
.gif)
- Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
For wire harness and connector inspection procedures and precautions, refer to "
"
PROCEDURE
READ VALUE USING GTS (NEUTRAL SWITCH)
(a) In accordance with the display on the GTS, read the Data List.
Powertrain > Stop and Start > Data ListNeutral Switch
OK:
Tester Display | Condition | Normal Condition |
|---|---|---|
Neutral Switch |
Shift lever in P or N |
ON |
Shift lever not in P or N |
OFF |
| OK | GO TO PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
CHECK VEHICLE SPECIFICATION
(a) Check the vehicle specification,
Result | Proceed to |
|---|---|
for 2WD |
A |
for AWD |
B |
| B | GO TO STEP 5 |
|
INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Click here ![]()
| NG | REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
(a) Disconnect the A169 engine stop and start ECU connector.
(b) Disconnect the C62 park/neutral position switch assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A169-21 (STA) - C62-5 (L) |
Always |
Below 1 Ω |
A169-17 (CLL) - C62-4 (B) |
Always |
Below 1 Ω |
A169-21 (STA) - Body ground |
Always |
80 to 180 Ω |
A169-17 (CLL) - Body ground |
Always |
10 kΩ or higher |
C62-5 (L) - Body ground |
Always |
80 to 180 Ω |
C62-4 (B) - Body ground |
Always |
10 kΩ or higher |
| OK | REPLACE ENGINE STOP AND START ECU |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Click here ![]()
| NG | REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
(a) Disconnect the A169 engine stop and start ECU connector.
(b) Disconnect the C62 park/neutral position switch assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A169-21 (STA) - C62-5 (L) |
Always |
Below 1 Ω |
A169-17 (CLL) - C62-4 (B) |
Always |
Below 1 Ω |
A169-21 (STA) - Body ground |
Always |
80 to 180 Ω |
A169-17 (CLL) - Body ground |
Always |
10 kΩ or higher |
C62-5 (L) - Body ground |
Always |
80 to 180 Ω |
C62-4 (B) - Body ground |
Always |
10 kΩ or higher |
| OK | REPLACE ENGINE STOP AND START ECU |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |