Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
DRAIN DIFFERENTIAL OIL |
- |
- |
- |
|
2 |
TAIL EXHAUST PIPE ASSEMBLY |
17430 |
- |
- |
|
3 |
PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY |
37100 |
- |
- |
- |
4 |
REAR STABILIZER BAR |
48812 |
- |
- |
- |
5 |
REAR DRIVE SHAFT ASSEMBLY LH |
42340B |
- |
- |
- |
6 |
REAR DRIVE SHAFT ASSEMBLY RH |
42330 |
- |
- |
- |
7 |
NO. 2 FUEL TANK PROTECTOR |
77642A |
- |
- |
- |
8 |
NO. 1 FUEL TANK PROTECTOR |
77641A |
- |
- |
- |
9 |
NO. 2 FLOOR WIRE |
82162 |
- |
- |
- |
10 |
REAR DIFFERENTIAL CARRIER ASSEMBLY |
- |
- |
- |
|
*1 |
REAR UPPER DIFFERENTIAL MOUNT STOPPER |
*2 |
REAR LOWER DIFFERENTIAL MOUNT STOPPER |
● |
Non-reusable part |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
11 |
NO. 7 FLOOR WIRE |
8216A |
- |
- |
- |
12 |
WIRE HARNESS CLAMP BRACKET |
- |
- |
- |
- |
13 |
REAR DIFFERENTIAL DYNAMIC DAMPER |
41196 |
- |
- |
- |
14 |
REAR NO. 1 DIFFERENTIAL SUPPORT |
52380 |
- |
- |
- |
15 |
REAR NO. 2 DIFFERENTIAL SUPPORT |
52380C |
- |
- |
- |
16 |
REAR DIFFERENTIAL SUPPORT |
52391B |
- |
- |
- |
*1 |
REAR DIFFERENTIAL CARRIER ASSEMBLY |
- |
- |
● |
Non-reusable part |
- |
- |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear differential carrier assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplacement Part or Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
Rear wheel alignment adjustment |
|
|
|
Reset memory |
Dynamic torque control AWD system |
||
Suspension, tires, etc. |
Rear television camera assembly optical axis (Back camera position setting) |
Parking assist monitor system |
|
Initialize headlight ECU sub-assembly LH |
Automatic headlight beam level control system |
CAUTION:
- When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

- Touching high-temperature areas such as the engine and exhaust pipe could result in burns.
PROCEDURE
1. DRAIN DIFFERENTIAL OIL
Click here ![]()
2. REMOVE TAIL EXHAUST PIPE ASSEMBLY
![]() |
Click here |
3. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
Click here ![]()
4. REMOVE REAR STABILIZER BAR
Click here ![]()
5. REMOVE REAR DRIVE SHAFT ASSEMBLY LH
Click here ![]()
6. REMOVE REAR DRIVE SHAFT ASSEMBLY RH
Click here ![]()
7. REMOVE NO. 2 FUEL TANK PROTECTOR
Click here ![]()
8. REMOVE NO. 1 FUEL TANK PROTECTOR
Click here ![]()
9. DISCONNECT NO. 2 FLOOR WIRE
10. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY
*1 |
Rear Upper Differential Mount Stopper |
*2 |
Rear Lower Differential Mount Stopper |
(1) Support the rear differential carrier assembly with a transmission jack.
NOTICE:
- The remaining oil may leak out when removing the rear differential carrier assembly.
- Securely support the rear differential carrier assembly while performing this step to avoid excessively tilting or dropping the rear differential carrier assembly.
(2) Remove the 3 bolts and 2 rear lower differential mount stoppers.
(3) Slowly lower the jack and then remove the rear differential carrier assembly and 2 rear upper differential mount stoppers from the rear suspension member sub-assembly.
11. REMOVE NO. 7 FLOOR WIRE
12. REMOVE WIRE HARNESS CLAMP BRACKET
13. REMOVE REAR DIFFERENTIAL DYNAMIC DAMPER
14. REMOVE REAR NO. 1 DIFFERENTIAL SUPPORT
15. REMOVE REAR NO. 2 DIFFERENTIAL SUPPORT
16. REMOVE REAR DIFFERENTIAL SUPPORT

.png)
.png)
.png)
.gif)