Removal
REMOVAL
COMPONENTS (REOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
TAIL EXHAUST PIPE ASSEMBLY |
17430 |
- |
- |
|
2 |
MAIN MUFFLER HEAT INSULATOR UPPER |
58327D |
- |
- |
- |
● |
Non-reusable part |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
3 |
SERVICE PLUG GRIP |
G3834 |
- |
- |
- |
4 |
REMOVE CONNECTOR COVER ASSEMBLY |
- |
- |
- |
|
5 |
CHECK TERMINAL VOLTAGE |
- |
- |
- |
|
6 |
INSTALL CONNECTOR COVER ASSEMBLY |
- |
- |
- |
|
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
7 |
DECK BOARD ASSEMBLY |
58410B |
- |
- |
- |
8 |
SPARE WHEEL CUSHION |
64777J |
- |
- |
- |
9 |
SEPARATE REAR TRACTION MOTOR CABLE |
G1149 |
- |
- |
|
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
10 |
REAR WHEEL |
- |
- |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
11 |
REAR AXLE SHAFT NUT LH |
42312B |
- |
- |
|
12 |
REAR AXLE SHAFT NUT RH |
42311N |
- |
- |
|
13 |
REAR FLEXIBLE HOSE LH |
47319F |
- |
- |
- |
14 |
REAR FLEXIBLE HOSE RH |
47318F |
- |
- |
- |
15 |
REAR SKID CONTROL SENSOR LH |
89544E |
- |
- |
|
16 |
REAR SKID CONTROL SENSOR RH |
89544D |
- |
- |
|
17 |
REAR STABILIZER LINK ASSEMBLY LH |
48840A |
- |
- |
|
18 |
REAR STABILIZER LINK ASSEMBLY RH |
48830D |
- |
- |
|
19 |
REAR STABILIZER BAR |
48812 |
- |
- |
- |
● |
Non-reusable part |
![]() |
Do not apply lubricants to the threaded parts |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
20 |
REAR COIL SPRING LH |
48231B |
- |
- |
- |
21 |
REAR COIL SPRING RH |
48231A |
- |
- |
- |
22 |
REAR LOWER COIL SPRING INSULATOR LH |
48258C |
- |
- |
- |
23 |
REAR LOWER COIL SPRING INSULATOR RH |
48258B |
- |
- |
- |
24 |
REAR NO. 1 SUSPENSION ARM ASSEMBLY LH |
48720A |
- |
- |
|
25 |
REAR NO. 1 SUSPENSION ARM ASSEMBLY RH |
48710A |
- |
- |
|
26 |
SEPARATE REAR UPPER CONTROL ARM ASSEMBLY LH |
48790 |
- |
- |
|
27 |
SEPARATE REAR UPPER CONTROL ARM ASSEMBLY RH |
48770A |
- |
- |
|
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
28 |
REAR DRIVE SHAFT ASSEMBLY LH |
42340B |
- |
- |
|
29 |
REAR DRIVE SHAFT ASSEMBLY RH |
42330 |
- |
- |
|
30 |
REAR SUSPENSION MEMBER SUB-ASSEMBLY |
51206A |
- |
- |
|
31 |
CONNECTOR COVER |
82821T |
- |
- |
|
32 |
MOTOR CABLE TERMINAL CAP |
G114D |
- |
- |
|
33 |
REAR TRACTION MOTOR CABLE |
G1149 |
- |
- |
|
34 |
NO. 6 FLOOR WIRE |
82169A |
- |
- |
- |
35 |
MOTOR CABLE BRACKET |
- |
- |
- |
- |
36 |
REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH |
48790 |
- |
- |
|
37 |
REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH |
48770A |
- |
- |
|
38 |
REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY |
G1050 |
- |
- |
|
39 |
REAR NO. 2 SUSPENSION ARM ASSEMBLY LH |
48740F |
- |
- |
|
40 |
REAR NO. 2 SUSPENSION ARM ASSEMBLY RH |
48730F |
- |
- |
|
41 |
DIFFERENTIAL MOUNT CUSHION |
41651G |
- |
- |
|
*1 |
NO. 2 CAMBER ADJUST CAM |
*2 |
REAR SUSPENSION TOE ADJUST CAM SUB-ASSEMBLY |
*3 |
DIFFERENTIAL DYNAMIC DAMPER |
- |
- |
● |
Non-reusable part |
![]() |
Do not apply lubricants to the threaded parts |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension crossmember sub-assembly removal/installation are shown below.
Necessary Procedures After Procedure PerformedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Rear wheel alignment adjustment |
|
|
|
Suspension, tires, etc. |
Rear television camera assembly optical axis (Back camera position setting) |
Parking Assist Monitor System |
|
Initialize headlight ECU subassembly LH |
Automatic headlight beam level control system |
||
Gas leak from exhaust system is repaired |
Inspection After Repair |
|
CAUTION:
- When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.
- Touching high-temperature areas such as the engine and exhaust pipe could result in burns.
PROCEDURE
1. REMOVE TAIL EXHAUST PIPE ASSEMBLY
Click here ![]()
2. REMOVE MAIN MUFFLER HEAT INSULATOR UPPER
Click here ![]()
3. REMOVE SERVICE PLUG GRIP
Click here ![]()
4. REMOVE CONNECTOR COVER ASSEMBLY
![]() |
Click here |
5. CHECK TERMINAL VOLTAGE
Click here ![]()
6. INSTALL CONNECTOR COVER ASSEMBLY
![]() |
Click here |
7. REMOVE DECK BOARD ASSEMBLY
Click here ![]()
8. REMOVE SPARE WHEEL CUSHION
Click here ![]()
9. SEPARATE REAR TRACTION MOTOR CABLE
![]() |
Click here |
10. REMOVE REAR WHEEL
Click here ![]()
11. REMOVE REAR AXLE SHAFT NUT LH
Click here ![]()
12. REMOVE REAR AXLE SHAFT NUT RH
(a) Perform the same procedure as for the LH side.
13. SEPARATE REAR FLEXIBLE HOSE LH
Click here ![]()
14. SEPARATE REAR FLEXIBLE HOSE RH
(a) Perform the same procedure as for the LH side.
15. DISCONNECT REAR SKID CONTROL SENSOR LH
Click here ![]()
16. DISCONNECT REAR SKID CONTROL SENSOR RH
(a) Perform the same procedure as for the LH side.
17. REMOVE REAR STABILIZER LINK ASSEMBLY LH
Click here ![]()
18. REMOVE REAR STABILIZER LINK ASSEMBLY RH
(a) Perform the same procedure as for the LH side.
19. REMOVE REAR STABILIZER BAR
Click here ![]()
20. REMOVE REAR COIL SPRING LH
Click here ![]()
21. REMOVE REAR COIL SPRING RH
(a) Perform the same procedure as for the LH side.
22. REMOVE REAR LOWER COIL SPRING INSULATOR LH
Click here ![]()
23. REMOVE REAR LOWER COIL SPRING INSULATOR RH
(a) Perform the same procedure as for the LH side.
24. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
Click here ![]()
25. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
(a) Perform the same procedure as for the LH side.
26. SEPARATE REAR UPPER CONTROL ARM ASSEMBLY LH
![]() |
NOTICE: Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured. |
27. SEPARATE REAR UPPER CONTROL ARM ASSEMBLY RH
(a) Perform the same procedure as for the LH side.
28. REMOVE REAR DRIVE SHAFT ASSEMBLY LH
Click here ![]()
29. REMOVE REAR DRIVE SHAFT ASSEMBLY RH
(a) Perform the same procedure as for the LH side.
30. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY
*a |
Engine Lifter |
*b |
Attachment |
![]() |
Attachment and Wooden Block Placement Location |
- |
- |
(1) Disconnect the connector.
(2) Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.
CAUTION:
- The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
- If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.
NOTICE:
Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.
(3) Remove the 2 bolts and 2 nuts.
(4) Slowly lower the rear suspension member sub-assembly.
NOTICE:
When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.
31. REMOVE CONNECTOR COVER
![]() |
Click here |
32. REMOVE MOTOR CABLE TERMINAL CAP
![]() |
Click here |
33. REMOVE REAR TRACTION MOTOR CABLE
Click here ![]()
34. REMOVE NO. 6 FLOOR WIRE
35. REMOVE MOTOR CABLE BRACKET
36. REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH
Click here ![]()
37. REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH
(a) Perform the same procedure as for the LH side.
38. REMOVE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY
Click here ![]()
39. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
Click here ![]()
40. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
(a) Perform the same procedure as for the LH side.
41. REMOVE DIFFERENTIAL MOUNT CUSHION
![]() |
NOTICE:
|
*a |
Hold |
*b |
Turn |
![]() |
Front of vehicle |
- |
- |
(1) Using SST, remove the differential mount cushion from the rear suspension member sub-assembly.
SST: 09570-48010
.png)
.png)
.png)
.gif)
.png)
.png)

.png)
.png)