VEHICLE CONTROL HISTORY (RoB)
VEHICLE CONTROL HISTORY (RoB)
DESCRIPTION
- Vehicle Control History is a function that captures and stores ECU data when triggered by specific vehicle behavior.
- It may be possible to determine the cause of the malfunction by checking the vehicle history information and freeze frame data.
- The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.
- The stored data items for Vehicle Control History Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The contents of the Freeze Frame Data are almost the same as those of the Data List.
Click here
.gif)
PRECAUTIONS
- As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History before performing any inspections.
- As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.
CHECK VEHICLE CONTROL HISTORY (POWER STEERING SYSTEM)
(a) Enter the following menus: Chassis / EMPS / Utility / Vehicle Control History (RoB).
Chassis > EMPS > UtilityVehicle Control History (RoB)
Vehicle Control History Item (Power Steering System)FFD Group | Code | Tester Display | Measurement Item | Diagnostic Note |
|---|---|---|---|---|
- |
X200C |
Vehicle Speed Signal Invalidity |
|
- |
- |
X206D |
Power Source Stop |
Latest Engine Stall/READY OFF Control History |
- |
- |
X206E |
High Load Continuation |
Latest High Load Continuous Control Number of Times |
- |
- |
X206F |
Prevention of ECU/Motor Overheat |
Latest Overheat Prevention Control History |
- |
- |
X208F |
Battery Voltage Drop |
|
- |
- |
X2600 |
Software Incompatibility with ENG/HV Control Module (Not Programmed) |
History stored when vehicle information (gasoline/HV) is not stored |
- |
- |
X2601 |
Software Inconsistency with ENG/HV Control Module |
|
- |
- |
X2603 |
Software Inconsistency with Body Control Module |
|
- |
- |
X2605 |
Software Inconsistency with Brake Control Module |
|
- |
- |
X2606 |
Software Inconsistency with Suspension Control Module |
|
- |
- |
X2610 |
Torque Sensor Missing Calibration of Adjustment Value Non-Memory |
History stored when zero point calibration not performed |
- |
- |
X2611 |
Torque Sensor Missing Calibration of Adjustment Incomplete |
History stored when zero point calibration failed |
- |
- |
X2612 |
Assist Map Non-Memory |
History stored when Assist Map Writing has not been performed |
- |
- |
XF021 |
Software Not Programmed |
At the time of software non-writing |
CLEAR VEHICLE CONTROL HISTORY (POWER STEERING SYSTEM)
(a) Enter the following menus: Chassis / EMPS / Utility / Vehicle Control History (RoB).
Chassis > EMPS > UtilityVehicle Control History (RoB)
(b) Press the DTC clear button.
NOTICE:
By performing this procedure, all stored Vehicle Control History items will be cleared.
VEHICLE CONTROL HISTORY FREEZE FRAME DATA (POWER STEERING SYSTEM)
(a) Enter the following menus: Chassis / EMPS / Utility / Vehicle Control History (RoB).
Chassis > EMPS > UtilityVehicle Control History (RoB)
(b) Select a vehicle control history item to access the applicable freeze frame data.
(c) Check the freeze frame Data recorded with the Vehicle Control History.
GTS Display | Description |
|---|---|
Total Distance Traveled |
Total distance traveled |
Total Distance Traveled - Unit |
Total Distance Traveled unit |
Vehicle Speed |
Vehicle speed from speedometer |
Engine Revolution |
Engine speed |
Ready Status |
Ready status |
Battery Voltage |
Auxiliary battery voltage |
Steering Wheel Torque |
Steering wheel torque |
Steering Angle Velocity |
Steering angle speed |
Steering Angle |
Steering angle |
Status of Vehicle Power (IGP PT2) |
State of IGP power source(PT2) |
Status of Vehicle Power (IGP PT1) |
State of IGP power source(PT1) |
Status of Vehicle Power (IGP PDC) |
State of IGP power source(PDC) |
Status of Vehicle Power (IGR PDC) |
State of IGR power source(PDC) |
Battery Voltage (System 2) |
Auxiliary battery voltage (System 2) |
IG Power Supply |
IG power source voltage |
PIG Power Supply |
PIG power source voltage |
Thermistor Temperature |
ECU substrate temperature |
Power Source |
Operating state of hybrid system |
PS Assist Signal |
Status of the record of power steering assist signal |
Synchronization Status of PWM |
Modulation synchronization state of the motor pulse wave duty ratio |
IG Power Supply (System 2) |
ECU power supply status (System 2) |
PIG Power Supply (System 2) |
PIG power supply voltage (System 2) |
Thermistor Temperature (System 2) |
ECU substrate temperature (System 2) |
Cooperation Control State |
Power steering operation control state |
Middle Voltage of Other Systems |
Middle voltage of other systems |
Middle Voltage of Other Systems (System 2) |
Middle voltage of other systems (System 2) |
Torque Sensor 1 Output |
Torque sensor 1 output value |
Torque Sensor 2 Output |
Torque sensor 2 output value |
Torque Sensor 3 Output |
Torque sensor 3 output value |
Torque Sensor 4 Output |
Torque sensor 4 output value |
Motor Actual Current (Q Axis) |
Detected current flow to motor (detected current of axis q) |
Command Value Current (Q Axis) |
Target current flow to motor (requested current of axis q) |
Motor Actual Current 2 (D Axis) |
Detected current flow to motor (detected current of axis d) |
Command Value Current 2 (D Axis) |
Target current flow to motor (requested current of axis d) |
Motor Rotation Angle |
Motor rotation angle (detected by rotation sensor) |
Final Motor Current limited (Q Axis) |
Final motor current set limit (request current of axis q) |
Motor Actual Current (Q Axis) (System 2) |
Motor current (Q axis) (System 2) |
Command Value Current (Q Axis) (System 2) |
Motor command current (Q axis) (System 2) |
Motor Actual Current 2 (D Axis) (System 2) |
Motor current 2 (D axis) (System 2) |
Command Value Current 2 (D Axis) (System 2) |
Motor command current 2 (D axis) (System 2) |
Motor Rotation Angle (System 2) |
Motor rotation angle (System 2) |
Final Motor Current Limited (Q Axis) (System 2) |
Final motor current limit value (Q axis) (System 2) |
CAN Vehicle Speed (SP1) |
Vehicle speed input value sent via CAN (equal to value indicated on speedometer) |
CAN Steering Angle Speed (SSAV) |
Steering wheel turning speed value sent via CAN |
ECU Overheat Prevention Part |
Internal component of ECU for which overheat protection control is performed |
ECU Estimate Temperature of Overheat Prevention Part |
Estimated temperature of internal component of ECU for which overheat protection control is performed |
Motor Overheat Prevention Part |
Internal component of motor for which overheat protection control is performed |
Motor Estimate Temperature of Overheat Prevention Part |
Estimated temperature of internal component of motor for which overheat protection control is performed |