Replacement

sst 09930–00010

1. Remove the 2 bolts, separate the brake caliper assy lh from the steering knuckle.

sst 09628–62011

1. Using a plastic hammer, separate the front drive shaft assy lh from the axle hub.

• be careful not to damage the boot.
• W/ abs: be careful not to damage the speed sensor rotor.

2. remove the 2 bolts, nuts and front axle assy lh.

1. 1
   Remove the cotter pin and nut.
2. 2
   using sst, remove the lower ball joint assy front lh.

   Sst 09628–62011

1. Using a snap ring pliers, remove the lh hole snap ring.

1. 1
   Using sst, remove the hub sub–assy lh.

   Sst 09520–00031

   

2. 2
   Using sst, remove the inner race of hub lh bearing from the hub sub–assy lh.

   Sst 09950–40011 (09951–04020, 09952–04010, 09953–04030, 09954–04010, 09955–04061, 09957–04010, 09958–04011), 09950–60010 (09951–00370)

1. remove the 3 bolts and dust cover front lh.

1. 1
   Place the inner race of hub lh bearing on the outer race of hub lh bearing.
2. 2
   using sst and a press, remove the hub lh bearing from the steering knuckle.

   Sst 09527–17011, 09950–60010 (09951–00640), 09950–70010 (09951–07100)

1. Using sst and a press, install a new hub lh bearing to the steering knuckle.

   Sst 09950–60020 (09951–00720), 09950–70010 (09951–07100)

1. install the dust cover front lh with the 3 bolts.

   Torque: 8.3 Nvm (85 Kgf·cm, 73 in.Vlbf)

1. Using sst and a press, install the hub sub–assy lh.

   Sst 09608–32010, 09950–60010 (09951–00600), 09950–70010 (09951–07100)

1. Using snap ring pliers, install a new lh hole snap ring.

1. 1
   install the lower ball joint assy front lh, torque the nut.

   Torque: 103 nvm (1,050 Kgf·cm, 76 ft·lbf)

2. 2
   install a new cotter pin.

1. 1
   Install the 2 bolts, nuts and front axle assy lh to the shock absorber. Torque: 153 nvm (1,560 Kgf·cm, 113 ft·lbf) Notice

   : only when reusing the bolts and nuts, apply engine oil to the screw part of the nuts.

2. 2
   push the front axle assy toward the outside of the vehicle, fit the splined part of the drive shaft assy to that of the front axle assy, insert the drive shaft assy into the front axle assy.

• do not push out the front axle assy excessively.
• Be careful not to damage the drive shaft outboard joint boot.
• W/ abs: be careful not to damage the speed sensor rotor.

1. Install the brake caliper assy lh with the 2 bolts to the steering knuckle.

   Torque: 106.8 Nvm (1,089 Kgf·cm, 79 ft·lbf)

1. using a socket wrench (30 mm), install a new hub lh nut.

   Torque: 216 nvm (2,203 Kgf·cm, 159 ft·lbf)

1. Using a dial indicator, check the backlash near the center of the axle hub.

   Maximum: 0.05 Mm (0.0020 In.)

If the backlash exceeds the maximum, replace the front axle hub bearing.

1. Using a dial indicator, check the deviation at the surface of the axle hub outside the hub bolt.

   Maximum: 0.05 Mm (0.0020 In.)

If the backlash exceeds the maximum, replace the front axle hub sub–assy.

1. Using a chisel and a hammer, stake the hub lh nut.

torque: 103 nvm (1,050 Kgf·cm, 76 ft·lbf)