Installation

Hint:

• Use the same procedures for the lh side and rh side.
• The procedures listed below are for the lh side.
• A bolt without a torque specification is shown in the standard bolt chart (see page ss-2).

1. Install rear no. 1 Seat outer belt assembly lh

1. Align the claws with the seat belt positioning holes, and install the retractor of the seat belt with the 2 bolts as shown in the illustration.

Torque: 8.5 N*m (87 kgf*cm, 75 in.*Lbf) for upper bolt 42 N*m (428 kgf*cm, 31 ft.*Lbf) for lower bolt

1. 1
   Connect the shoulder anchor with the bolt.
2. 2
   Install inner roof side garnish assembly lh (w/ rear no. 2 Seat) (see page ir-52)
3. 3
   Install rear no. 2 Seat outer belt assembly lh (w/ rear no. 2 Seat)

   

Torque: 42 n*m (428 kgf*cm, 31 ft.*Lbf)

1. Align the claws with the seat belt positioning holes and install the retractor of the seat belt with the 2 bolts as shown in the illustration.

Torque: 8.5 N*m (87 kgf*cm, 75 in.*Lbf) for upper bolt 42 N*m (428 kgf*cm, 31 ft.*Lbf) for lower bolt

2. Connect the shoulder anchor with the bolt.

Torque: 42 n*m (428 kgf*cm, 31 ft.*Lbf)

Close the cover cap.

1. 1
   Install inner roof side garnish assembly lh (w/o rear no. 2 Seat) (see page ir-51)
2. 2
   Install deck trim side panel assembly lh (w/ rear no. 2 Seat) (see page ir-53)
3. 3
   Install deck trim side panel assembly lh (w/ o rear no. 2 Seat) (see page ir-52)
4. 4
   Connect rear no. 2 Seat outer belt assembly lh (w/ rear no. 2 Seat)

   

1. Connect the seat belt's floor anchor with the bolt.

Torque: 42 n*m (428 kgf*cm, 31 ft.*Lbf)

Close the cover.

8. Connect rear no. 1 Seat outer belt assembly lh

1. Connect the seat belt's floor anchor with the bolt.

Torque: 42 n*m (428 kgf*cm, 31 ft.*Lbf)

Attach the lap belt outer anchor cover.

1. 1
   Install reclining remote control lever bezel lh (w/o rear no. 2 Seat)
2. 2
   Install rear floor finish plate (see page ir- 55)
3. 3
   Install rear no. 1 Floor mat support side plate (see page ir-55)
4. 4
   Install rear floor no. 3 Board
5. 5
   Install rear floor no. 2 Board
6. 6
   Install rear no. 2 Seat assembly lh (w/ rear no. 2 Seat) (see page se-121)
7. 7
   Install rear no. 2 Seat assembly rh (w/ rear no. 2 Seat) (see page ir-55)
8. 8
   Install no. 2 Seat leg cover lh (w/ rear no. 2 Seat) (see page se-123)
9. 9
   Install no. 2 Seat leg cover rh (w/ rear no. 2 Seat) (see page ir-56)
10. 10
    Install no. 2 Seat hinge cover lh (w/ rear no.

2 Seat) (see page se-123)

Remove no. 2 Seat hinge cover rh (w/ rear no.

2 Seat) (see page ir-56)

Install deck board assembly (w/o rear no. 2 Seat)

Install rear floor no. 1 Board (w/o rear no.

2 Seat)

Install tonneau cover assembly (w/o rear no. 2 Seat)

Install package tray trim pocket subassembly (w/o rear no. 2 Seat)

Install rear door opening trim weatherstrip lh

Install rear door scuff plate lh (see page ir-57)

Connect cable to negative battery terminal