Reassembly

Caution: Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands. Hint:

A bolt without a torque specification is shown in the standard bolt chart (see page ss-2).

1. Install rear seat cover lh

1. 1
   Attach the 2 claws to install the cover.
2. 2
   Install the 2 screws.
3. 3
   Install rear seatback cover lh

   

1. 1
   Attach the 2 claws to install the cover.
2. 2
   Install the 2 screws.
3. 3
   Install rear no. 1 Seatback cover

Notice:

• Be careful not to damage the cover.
• When installing the hog rings, avoid wrinkling the cover.

1. 1
   Using hog ring pliers, install the seatback cover to the seatback pad with 3 new hog rings.
2. 2
   Install the seatback cover (with pad) to the seatback frame.

   

3. Attach the 4 claws to install the 2 headrest supports.

1. 1
   Lift up the seatback cover and install the 13 hog rings.
2. 2
   Install rear seatback protector

   

1. Install the protector with the 2 nuts.

Torque: 20 n*m (204 kgf*cm, 15 ft.*Lbf)

Attach the clip.

1. 1
   Attach the clips and close the fastening tape.
2. 2
   Install rear seat lap type center belt assembly lh (see page sb-41)
3. 3
   Install rear no. 1 Seatback assembly lh

   

1. Install the seatback with the 5 bolts.

Torque: 42 n*m (428 kgf*cm, 31 ft.*Lbf)

1. 1
   W/o rear no. 2 Seat: attach the 2 clamps and connect the cable to the reclining adjuster.
2. 2
   Install rear seatback lock control lever base lh

   

1. 1
   Attach the 2 claws to install the lever base.
2. 2
   Install the screw.
3. 3
   Install rear seat reclining release lever

   

1. Attach the claw to install the release lever.

1. 1
   Install the cover with the 2 screws.
2. 2
   Install rear seat cushion moulding lh

   

1. 1
   Attach the 2 claws to install the moulding.
2. 2
   Install the screw.
3. 3
   Install rear seat cushion rear moulding lh

   

1. 1
   Attach the claw to install the moulding.
2. 2
   Install the screw.
3. 3
   Install rear seat rear bracket cover lh

   

1. 1
   Open the lower part of the seatback cover. Then attach the 4 clips to install the bracket cover.
2. 2
   Install the 2 screws.
3. 3
   Install rear no. 1 Seat cushion cover

Notice:

• Be careful not to damage the cover.
• When installing the hog rings, avoid wrinkling the cover.

1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 3 new hog rings.

2. Using hog ring pliers, install the seat cushion cover (with pad) to the seat cushion frame with 29 new hog rings.

1. 1
   Attach the 2 hooks.
2. 2
   Install rear no. 1 Seat cushion assembly lh

   

1. Install the cushion with the 2 bushes and 2 bolts.

Torque: 21 n*m (214 kgf*cm, 15 ft.*Lbf)

2. Install the 2 bolts.

Torque: 21 n*m (214 kgf*cm, 15 ft.*Lbf)

Connect the rubber band of the seatback cover to the seat cushion frame.

1. 1
   Install rear seat inner belt assembly rh (see page sb-41)
2. 2
   Install rear seat cushion lower hinge cover lh

   

1. 1
   Attach the 5 claws to install the hinge cover.
2. 2
   Install rear no. 3 Seat cushion hinge cover

   

1. 1
   Attach the 6 claws to install the hinge cover.
2. 2
   Install rear no. 1 Seat armrest assembly lh

   

1. 1
   Install the armrest with the 2 nuts.
2. 2
   Install rear seat center armrest cover

   

Torque: 32 n*m (326 kgf*cm, 24 ft.*Lbf)

1. Push the armrest cover in the direction indicated by the arrow in the illustration to attach the 2 claws.

1. 1
   Attach the 2 clips to install the armrest cover.
2. 2
   Install rear seat center armrest assembly

   

1. 1
   Install the armrest with the 2 nuts.
2. 2
   Install center armrest hinge cover lh

   

Torque: 32 n*m (326 kgf*cm, 24 ft.*Lbf)

1. 1
   Attach the 4 claws to install the hinge cover.
2. 2
   Install center armrest hinge cover rh
3. 3
   Pass the seat lock release strap through the hole in the hinge cover.
4. 4
   Attach the claw to install the hinge cover.

   

1. 1
   Install the 2 screws and 2 rear seatback lock hooks.
2. 2
   Install rear seat center headrest assembly
3. 3
   Install rear seat headrest assembly