Reassembly

Hint:

• Use the same procedures for the rh side and lh side.
• The procedures listed below are for the lh side.

1. 1
   Install seat lock release band
2. 2
   Install the band with nut.

Hint:

After installing the band, feed it through the seatback frame hole towards the rear of the vehicle.

2. Install reclining lock release band

Hint:

Use the same procedures described for the lh side.

3. Install seatback lock control cable assembly

1. 1
   Install the cable to the seatback frame as shown in the illustration.
2. 2
   Install rear seat reclining inner cover lh

   

1. 1
   Attach the 2 claws to install the inner cover.
2. 2
   Install rear seat reclining inner cover rh

Hint:

Use the same procedures described for the lh side.

6. Install rear no. 2 Seatback cover

Notice:

• Be careful not to damage the cover.
• When installing the hog rings, avoid wrinkling the cover.

1. 1
   Using hog ring pliers, install the seatback cover to the seatback pad with 3 new hog rings.
2. 2
   Install the seatback cover (with pad) to the seatback frame.

   

1. 1
   Attach the 4 claws to install the 2 headrest supports.
2. 2
   Using hog ring pliers, install 19 new hog rings.
3. 3
   Install rear seatback board carpet assembly lh

   

1. Pass the 2 release bands through the 2 holes in the seatback board carpet.

2. Attach the 9 clips to install the carpet.

Hint:

Make sure that the release band is not inside the seatback board carpet.

8. Install rear seatback lock control bezel

1. 1
   Pass the 2 release bands through the 2 holes in the 2 bezels.
2. 2
   Attach the 2 claws to install the 2 bezels.
3. 3
   Install the 2 screws.
4. 4
   Install the 4 seatback lock hooks.
5. 5
   Install rear no. 2 Seat headrest assembly
6. 6
   Install rear seat cushion wire subassembly

   

1. 1
   Install the wire with the nut.
2. 2
   Install seat lock control cable assembly

   

Torque: 18 n*m (184 kgf*cm, 13 ft.*Lbf)

1. Install the 5 cables to the seat cushion spring as shown in the illustration.

2. Clamp the cables to the seat cushion spring with 4 new cable ties as shown in the illustration.

1. 1
   Cut off the 2 cable ties, as shown in the illustration.
2. 2
   Attach the 2 clamps of the cable tie to the seat cushion spring.
3. 3
   Install rear no. 2 Seat cushion cover lh

   

Notice:

• Be careful not to damage the cover.
• When installing the hog rings, avoid wrinkling the cover.

1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 5 new hog rings.

2. Attach the hooks and install the seat cushion cover (with pad) to the seat cushion spring.

1. 1
   Attach the 5 hooks.
2. 2
   Install the 2 clips.
3. 3
   Install rear no. 2 Seat inner belt assembly lh (see page sb-40)
4. 4
   Remove rear no. 2 Seat cushion assembly

   

1. Install the seat cushion to the seatback with the 4 bolts.

Torque: 42 n*m (428 kgf*cm, 31 ft.*Lbf)

2. Connect the seat lock control cable of the rh side to the seatback as shown in the illustration.

1. 1
   Connect the seat lock control cable of the back side to the seat cushion as shown in the illustration.
2. 2
   Close the seat cushion cover and install the 2 clips.
3. 3
   Install no. 1 Rear seat reclining cover lh

   

1. 1
   Attach the 5 claws to install the cover.
2. 2
   Install the 2 screws.
3. 3
   Install no. 2 Rear seat reclining cover lh

   

1. 1
   Attach the clip and 5 claws to install the cover.
2. 2
   Install the 2 screws.