Disassembly

HINT: On the RH side, use the same procedures as on the LH side.

1. REMOVE REAR DOOR WINDOW FRAME MOULDING REAR LH (See page ET-30)

2. REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY LH (See page ET-21)

3. REMOVE SLIDE DOOR WINDOW GARNISH LH

1. 1
   Fully open the slide door window.
2. 2
   Remove the glass run.
3. 3
   Using a screwdriver, disengage the clip and remove the garnish.

   HINT: Tape the screwdriver tip before use.

4. 4
   Using a screwdriver, disengage the 2 claws and remove the weatherstrip inner from the garnish.

   HINT: Tape the screwdriver tip before use.

4. REMOVE SIDE TRIM BOARD COVER REAR LH

1. 1
   Remove the 2 screws.
2. 2
   Using a screwdriver, disengage the 8 claws and remove the cover together with the window control switch.

   HINT: Tape the screwdriver tip before use.

3. 3
   Remove the 2 screws and window control switch.

5. REMOVE REAR DOOR TRIM BOARD SUBASSEMBLY LH

1. 1
   Remove the screw.
2. 2
   Using a screwdriver, disengage the 9 clips and remove the trim board.

HINT:

• Tape the screwdriver tip before use.
• In order to prevent the door panel from being damaged, cover the areas with protective tape as indicated by arrow marks in the illustration.

1. 1
   Using a clip remover, remove the 6 clips and weatherstrip No. 2.
2. 2
   Using a screwdriver, disengage the 11 claws and remove the weatherstrip inner from trim board.

HINT: Tape the screwdriver tip before use.

1. 1
   w/ Sunshade: Remove the sunshade.
2. 2
   Remove the 7 screws and sunshade bezel.
3. 3
   Remove the 4 screws and curtain.

6. REMOVE SLIDE DOOR WINDOW ASSEMBLY LH

1. 1
   w/ Sunshade: Remove the sunshade hook.
2. 2
   Remove the bolt and window frame.

   

3. 3
   Remove the bolt.
4. 4
   Loosen the nut.
5. 5
   Push the window frame rear lower in the direction indicated by the arrow mark in the illustration.

   

6. 6
   Remove the 2 hole plugs.
7. 7
   Move the window until the bolts appear in the service holes.

NOTICE:

• Do not damage the window assembly.
• When the bolts are removed, the window assembly may fall and become deformed.

8. Remove the 2 bolts and window.

7. REMOVE REAR DOOR GLASS WEATHERSTRIP ASSEMBLY OUTER LH

8. REMOVE SLIDE DOOR ATTACHMENT CONTROL LH

1. 1
   Remove the 2 screws, bolt and inside handle.

   

2. 2
   Disconnect the connectors from the lock actuator and power window regulator motor.
3. 3
   Disengage the control cables.
4. 4
   Remove the 8 bolts and attachment control.

   

5. 5
   Remove the nut and the window frame rear lower.

NOTICE: When the nut is removed, the window frame may fall and become deformed.

HINT: Remove the window frame rear lower through the service hole.

1. 1
   Remove the control rod.
2. 2
   Remove the 3 bolts and lock remote control.

   

3. 3
   Remove the 2 screws and lock actuator

   

4. 4
   Remove the 3 screws and power window regulator motor.

   

5. 5
   Remove the half stop control lever and door lock control bellcrank.
6. 6
   Remove the 4 bolts and window regulator.

9. REMOVE REAR DOOR STIFFENER CUSHION LH

1. 1
   Remove 2 hole plugs.
2. 2
   Remove the 2 screws, clip and stiffener cushion.

   HINT: Remove the stiffener cushion through the service hole.

3. 3
   Remove the 2 grommets and 2 clips.

10. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH

1. 1
   Remove the hole plug.
2. 2
   Using a torx socket wrench (T30), loosen the screw and remove the outside handle cover with the lock key cylinder installed.

11. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

1. 1
   Pushing and pulling the outside handle in the direction indicated by the arrow mark in the illustration, remove the outside handle.
2. 2
   Remove the outside handle pads front and rear.

12. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

1. 1
   Remove the open rod to the outside handle frame.
2. 2
   Using a torx socket wrench (T30), loosen the screw.
3. 3
   Slide the outside handle frame in the direction indicated by the arrow mark in the illustration and remove it.

HINT: Remove the outside handle frame through the service hole.

13. REMOVE SLIDE DOOR LOCK ASSEMBLY FRONT LH

1. 1
   Remove the 2 cables.
2. 2
   Using a torx socket wrench (T30), remove the 3 screws and lock.

HINT: Remove the lock through the service hole.

14. REMOVE REAR DOOR LOCK ASSEMBLY LH

1. 1
   Remove the cable.
2. 2
   Using the torx socket wrench (T30), remove the 3 screws and lock.

HINT: Remove the lock through the service hole.

15. REMOVE REAR DOOR WIRE SUB-ASSEMBLY LH

1. 1
   Remove the 2 screws.
2. 2
   Using a screwdriver, remove the 2 clips and door wire.

HINT: Tape the screwdriver tip before use.