Toyota Sienna Quiz
Windshield / windowglass

Installation

In this manual: Windshield / windowglass
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
10steps
~60min
3/5difficulty
Done 0 of 10

1. INSTALL BACK DOOR GLASS

INSTALL BACK DOOR GLASS
  1. Clean and shape the contact surface of the vehicle body.
  2. Using a knife, cut away any rough adhesive on the contact surface of the body to ensure the appropriate surface shape.

HINT: Leave as much adhesive on the body as possible.

  • Clean the contact surface of the body with a shop rag saturated with cleaner.

    • HINT: Even if all the adhesive has been remove, clean the body.
    1. Using a brush, coat the exposed part of the body on the vehicle side with Primer M.
    INSTALL BACK DOOR GLASS

    NOTICE:

    • Allow the primer coating to dry for 3 minutes or more.
    • Do not coat the adhesive with Primer M.
    • Do not keep any of the opened Primer M for later use.
    1. Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.

    HINT: If an area other than that specified is coated by accident, wipe of the primer with a clean shop rag before it dries.

    NOTICE:

    • Allow the primer coating to dry for 3 minutes or more.
    • Do not keep any of the opened Primer G for later use.
    INSTALL BACK DOOR GLASS

    Dimensions:

    Dimensions
    1. Apply adhesive.

    Adhesive: Part No. 08850-00801 or equivalent

    1. Cut off the tip of the cartridge nozzle, as shown in the illustration.

    HINT: After cutting off the tip, use all adhesive within the time described in the table below.

    Tackfree time

    Tackfree time
    1. Load the sealer gun with the cartridge.
    2. Coat the glass with adhesive, as shown in the illustration.
      INSTALL BACK DOOR GLASS

    Dimensions:

    Dimensions
    1. Install the glass to the body.
    2. Hold the back window glass in place securely with tape or equivalent to the body until the adhesive has hardened.

    NOTICE:

    • Allow the primer coating to dry for 3 minutes or more.
    • Check that the clips are attached to the body correctly.
    • Check the clearance between the body and glass.
    1. Lightly press the front surface of the glass to ensure a close fit.
    2. Using a scraper, remove any excess or protruding adhesive.

    HINT: Apply adhesive onto the glass rim.

    NOTICE: Take care not to drive the vehicle for the time described in the table below.

    Minimum time

    Minimum time

    2. CHECK FOR LEAKAGE AND REPAIR

    CHECK FOR LEAKAGE AND REPAIR
    1. Conduct a leak test after the adhesive has completely hardened.
    2. Seal any leaks with auto glass sealer.

    3. INSTALL REAR WIPER MOTOR AND BRACKET ASSEMBLY

    4. INSTALL REAR WIPER ARM

    5. INSTALL FRONT WIPER ARM HEAD CAP

    6. INSTALL REAR SPOILER COVER (W/ REAR SPOILER)

    7. INSTALL BACK DOOR SERVICE HOLE PLATE

    8. INSTALL BACK DOOR TRIM BOARD ASSEMBLY

    9. INSTALL BACK DOOR PULL STRAP

    10. INSTALL BACK DOOR STRAP COVER

    11. INSTALL BACK DOOR SIDE GARNISH RH

    12. INSTALL BACK DOOR SIDE GARNISH LH

    13. INSTALL BACK DOOR GARNISH CENTER

    Test yourself

    A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.