Toyota Sienna Quiz
Supplemental restraint system

Open in Driver Side Squib Circuit

In this manual: Supplemental restraint system
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
24steps
~149min
5/5difficulty
1special tools
Done 0 of 24

DTC B0101/14 Open in Driver Side Squib Circuit

DESCRIPTION

The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0101/14 is recorded when an open circuit is detected in the driver side squib circuit

DTC No.

DTC Detecting Condition

Trouble Area
B0101/14
  • Open circuit in D+ wire harness or D- wire harness of driver side squib
  • Driver side squib malfunction
  • Spiral cable malfunction
  • Center airbag sensor assembly malfunction
  • Steering pad (Driver side squib)
  • Spiral cable
  • Center airbag sensor assembly
  • Instrument panel wire

INSPECTION PROCEDURE

HINT:

  • Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (8).
  • After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK STEERING PAD (DRIVER SIDE SQUIB)

CHECK STEERING PAD (DRIVER SIDE SQUIB)
  1. Turn the ignition switch to the LOCK position.
  2. ) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. ) Disconnect the connectors from the steering pad.
  4. Connect the white wire side of SST (resistance 2.1 Ω) to the spiral cable.

CAUTION: Never connect a tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3. Clear the DTCs stored in memory (5).
  4. Turn the ignition switch to the LOCK position.
  5. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6. Check the DTCs (5).

OK: DTC B0101/14 is not output.

HINT: Codes other than DTC B0101/14 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE STEERING PAD

2 CHECK DRIVER SIDE SQUIB CIRCUIT

CHECK DRIVER SIDE SQUIB CIRCUIT
  1. Turn the ignition switch to the LOCK position.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the SST (resistance 2.1 Ω) from the spiral cable.
  4. ) Disconnect the connector from the center airbag sensor assembly.
  5. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

Go to step 4

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY
  1. Connect the connectors to the steering pad and the center airbag sensor assembly.
  2. Connect the negative (-) terminal cabl to the battery, and wait for at least 2 seconds.
  3. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4. Clear the DTCs stored in memory (5).
  5. Turn the ignition switch to the LOCK position.
  6. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7. Check the DTCs (5).

OK: DTC B0101/14 is not output.

HINT: Codes other than code B0101/14 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

4 CHECK INSTRUMENT PANEL WIRE

CHECK INSTRUMENT PANEL WIRE
  1. Disconnect the instrument panel wire connector from the spiral cable.
  2. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

5 CHECK SPIRAL CABLE

CHECK SPIRAL CABLE
  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPLACE SPIRAL CABLE

USE SIMULATION METHOD TO CHECK

Test yourself

A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.