Toyota Sienna Quiz
Seat

Reassembly

In this manual: Seat
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
~2min read

1. INSTALL NO. 2 SEAT LEG SUB-ASSEMBLY

INSTALL NO. 2 SEAT LEG SUB-ASSEMBLY
  1. Install the No. 2 seat leg sub-assembly with the 3 bolts and nut.

    Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE: Tighten the bolts and nuts in the order shown in the illustration.

  1. Install the 3 clamps.

2. INSTALL NO. 2 SEAT CUSHION FRAME SUBASSEMBLY

3. INSTALL NO. 2 SEAT CUSHION SPRING ASSEMBLY

4. INSTALL NO. 2 SEAT CUSHION STOPPER

5. INSTALL REAR SEAT WIRE

6. INSTALL NO. 2 SEAT CUSHION PAD

7. INSTALL NO. 2 SEAT CUSHION COVER SUBASSEMBLY

  1. Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly to the No. 2 seat cushion pad with 6 new hog rings.

NOTICE:

  • Be careful not to damage the cover.
  • When installing the hog rings, take care to minimize wrinkles as much as possible.
INSTALL NO. 2 SEAT CUSHION COVER SUBASSEMBLY

8. INSTALL NO. 2 SEAT CUSHION COVER SUBASSEMBLY WITH PAD

9. INSTALL REAR SEAT COVER

10. INSTALL REAR NO. 2 SEAT BELT ASSEMBLY INNER

INSTALL REAR NO. 2 SEAT BELT ASSEMBLY INNER
  1. Install the rear No. 2 seat belt assembly inner with the bolt and washer.

    Torque: 44 N*m (449 kgf*cm, 33 ft.*lbf)

11. INSTALL REAR POWER SEAT SWITCH

12. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL

13. INSTALL NO. 2 SEATBACK FRAME SUB-ASSEMBLY

INSTALL NO. 2 SEATBACK FRAME SUB-ASSEMBLY
  1. Install the No. 2 seatback frame sub-assembly with the 4 bolts.

    Torque: 44 N*m (449 kgf*cm, 33 ft.*lbf)

NOTICE:

  • Tighten the bolts in the following order:
  • Temporarily tighten bolt (1).
  • Temporarily tighten bolt (2).
  • Fully tighten bolt (3).
  • Fully tighten bolt (4).
  • Fully tighten bolt (1).
  • Fully tighten bolt (2).

14. INSTALL FOLD SEAT CONTROL ECU

15. INSTALL NO. 2 SEATBACK PAD

16. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY

  1. Using hog ring pliers, install the No. 2 seatback cover sub-assembly to the No. 2 seatback pad with 6 new hog rings.

NOTICE:

  • Be careful not to damage the cover.
  • When installing the hog rings, take care to minimize wrinkles as much as possible
INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY

17. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY WITH PAD

18. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY RH

19. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY LH

20. INSTALL REAR SEAT HEADREST ASSEMBLY

21. INSTALL REAR SEAT RECLINING COVER RH

22. INSTALL REAR SEAT RECLINING COVER LH

23. INSTALL REAR NO. 2 SEAT COVER BEZEL

Test yourself

A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.