Toyota Tacoma Quiz
Park Assist / Monitoring

Blind Spot Monitor Main Switch

In this manual: Park Assist / Monitoring
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~2min read
Components COMPONENTS ILLUSTRATION Removal Removal REMOVAL PROCEDURE

1. REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL

(See page 2. REMOVE BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY) )

2. REMOVE BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)

(a) Disengage the 2 claws to remove the blind spot monitor main switch (warning canceling switch assembly).
Inspection INSPECTION PROCEDURE

1. INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)

(a) Measure the resistance according to the value(s) in the table below.

Text in Illustration

*a

Component without harness connected

(Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly))

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

4 (B) - 1 (D)

Blind spot monitor main switch on

Below 1 Ω

Blind spot monitor main switch off

10 kΩ or higher

If the result is not as specified, replace the blind spot monitor main switch (warning canceling switch assembly).

(b) Check that the switch illuminates.

(1) Apply battery voltage to the blind spot monitor main switch (warning canceling switch assembly) and check that the switch illuminates.

Text in Illustration

*a

Component without harness connected

(Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly))

OK:

Connection

Specified Condition

Battery positive (+) → Terminal 3 (ILL+)

Battery negative (-) → Terminal 2 (ILL-)

Illuminates

If the result is not as specified, replace the blind spot monitor main switch (warning canceling switch assembly).

(c) Check that the switch indicator operates.

(1) Apply battery voltage to the blind spot monitor main switch (warning canceling switch assembly) and check that the switch indicator operates.

Text in Illustration

*a

Component without harness connected

(Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly))

OK:

Connection

Switch Condition

Specified Condition

Battery positive (+) → Terminal 4 (B)

Battery negative (-) → Terminal 5 (E)

Blind spot monitor main switch on

Indicator Illuminates

If the result is not as specified, replace the blind spot monitor main switch (warning canceling switch assembly).
Installation INSTALLATION PROCEDURE

1. INSTALL BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)

(a) Engage the 2 claws to install the blind spot monitor main switch (warning cancel switch assembly).

2. INSTALL INSTRUMENT PANEL LOWER CENTER FINISH PANEL

(See page Blind Spot Monitor Sensor )

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.