Toyota Tacoma Quiz
2gr-fks Fuel

Fuel Pressure Sensor

In this manual: 2gr-fks Fuel
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~2min read
Components COMPONENTS ILLUSTRATION Inspection Inspection INSPECTION PROCEDURE

1. INSPECT FUEL DELIVERY PIPE SUB-ASSEMBLY (FUEL PRESSURE SENSOR)

NOTICE:

  • Do not remove the fuel pressure sensor from the fuel delivery pipe sub-assembly.
  • If a fuel pressure sensor is removed, replace the fuel delivery pipe sub-assembly with a new one.

(a) Remove the fuel delivery pipe sub-assembly (See page (b) Check the fuel pressure sensor output voltage. ).

(b) Check the fuel pressure sensor output voltage.

(1) Apply 5 V between terminals 1 (VC) and 3 (E2).

Text in Illustration

*a

Component without harness connected

(Fuel Pressure Sensor)

*b

Voltage applied between terminals

NOTICE:

  • Be careful when connecting the leads, as the fuel pressure sensor may be damaged if the leads are connected to the wrong terminals.
  • Do not apply more than 6 V to terminals 1 (VC) and 3 (E2).

HINT:

If a stable power supply is not available, use 4 1.2 V nickel-metal hydride batteries or equivalent.

(2) Measure the voltage between terminals.

Text in Illustration

*a

Component without harness connected

(Fuel Pressure Sensor)

Standard Voltage:

Tester Connection

Condition

Specified Condition

2 (PFL) - 3 (E2)

Pressure not applied to fuel pressure sensor

Approximately 0.56 to 0.94 V

If the result is not as specified, replace the fuel delivery pipe sub-assembly.

(c) Install the fuel delivery pipe sub-assembly (See page Installation ).

Installation INSTALLATION CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the fuel delivery pipe sub-assembly (fuel pressure sensor) (See page PROCEDURE ).

PROCEDURE

1. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY (FUEL PRESSURE SENSOR)

(See page )

NOTICE:

  • Do not remove the fuel pressure sensor from the fuel delivery pipe sub-assembly.
  • If a fuel pressure sensor is removed, replace the fuel delivery pipe sub-assembly (fuel pressure sensor) with a new one.

HINT:

Perform "Inspection After Repairs" after replacing the fuel delivery pipe sub-assembly (fuel pressure sensor) (See page Removal ).

Removal REMOVAL PROCEDURE

1. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY (FUEL PRESSURE SENSOR)

(See page )

NOTICE:

  • Do not remove the fuel pressure sensor from the fuel delivery pipe sub-assembly.
  • If a fuel pressure sensor is removed, replace the fuel delivery pipe sub-assembly (fuel pressure sensor) with a new one.

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.