DESCRIPTION
This DTC is stored when LIN communication between the front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
DTC No. | DTC Detection Condition | Trouble Area |
B2322 |
No communication between the front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more. |
- Front power window regulator motor assembly RH
- Main body ECU (multiplex network body ECU)
- Driver side junction block assembly
- Harness or connector
|
WIRING DIAGRAM
NOTICE:
HINT:
DTC B2325 is output when the communication between all of the following components and main body ECU (multiplex network body ECU) stops.
Click here 
PROCEDURE
CLEAR DTC
(a) Clear the DTCs.
Click here 
| NEXT |
 |
|
CHECK FOR DTC
(a) Check for DTCs.
Click here 
| DTC B2322 is not output |
 |
USE SIMULATION METHOD TO CHECK |
| DTC B2322 is output |
 |
|
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
(a) Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click here 
(b) Disconnect the M11 front power window regulator motor assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
A-16 (LIN2) - M11-9 (LIN) |
Always |
Below 1 Ω |
A-16 (LIN2) - Body ground |
Always |
10 kΩ or higher |
| NG |
 |
GO TO STEP 7 |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND)
*a |
Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly RH) |
(a) Disconnect the front power window regulator motor assembly RH connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
M11-1 (GND) - Body ground |
Always |
Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
M11-2 (B) - Body ground |
Always |
11 to 14 V |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
(a) Temporarily replace the front power window regulator motor assembly RH with a new or normally functioning one.
Click here 
(b) Clear the DTCs.
Click here 
| NEXT |
 |
|
CHECK FOR DTC
(a) Check for DTCs.
Click here 
| DTC B2322 is not output |
 |
END (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH IS DEFECTIVE) |
| DTC B2322 is output |
 |
REPLACE BODY ECU (MULTIPLEX NETWORK BODY ECU) |
CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
(a) Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click here 
(b) Disconnect the M11 front power window regulator motor assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
3I-17 - M11-9 (LIN) |
Always |
Below 1 Ω |
3I-17 - Body ground |
Always |
10 kΩ or higher |
| OK |
 |
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|