TERMINALS OF ECU
*A |
Main Body ECU (Multiplex Network Body ECU) with 1 connector |
- |
- |
*1 |
Main Body ECU (Multiplex Network Body ECU) |
- |
- |
*A |
Main Body ECU (Multiplex Network Body ECU) with 3 connectors |
- |
- |
*1 |
Main Body ECU (Multiplex Network Body ECU) |
- |
- |
1. CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
(a) Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click here 
(b) Connect the driver side junction block assembly connectors.
(c) Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
A-32 (IG) - Body ground |
None - Body ground |
Ignition power supply |
Ignition switch ON |
11 to 14 V |
Ignition switch off |
Below 1 V |
A-31 (BECU) - Body ground |
None - Body ground |
Battery power supply |
Always |
11 to 14 V |
A-30 (ACC) - Body ground |
None - Body ground |
ACC power supply |
Ignition switch ACC |
11 to 14 V |
Ignition switch off |
Below 1 V |
A-11 (GND1) - Body ground |
None - Body ground |
Ground |
Always |
Below 1 Ω |
(d) Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly.
Click here 
(e) Measure the pulse according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
A-16 (LIN2) - Body ground |
None - Body ground |
LIN communication line |
Ignition switch ON |
Pulse generation |
2. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Power Window Control System [w/ Jam Protection Function])
(a) Disconnect the N2 power window regulator master switch assembly connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
N2-3 (B) - N2-1 (E) |
R - W-B |
Battery power supply |
Always |
11 to 14 V |
N2-1 (E) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
3. CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Power Window Control System [w/ Jam Protection Function])
(a) Disconnect the N12 front power window regulator motor assembly LH connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
N12-2 (B) - N12-1 (GND) |
P - W-B |
Battery power supply |
Always |
11 to 14 V |
N12-1 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
4. CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Power Window Control System [w/ Jam Protection Function])
(a) Disconnect the M11 front power window regulator motor assembly RH connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
M11-2 (B) - M11-1 (GND) |
V - W-B |
Battery power supply |
Always |
11 to 14 V |
M11-1 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
5. CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (w/ Sliding Roof System)
(a) Disconnect the W3 sliding roof drive gear sub-assembly connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
W3-9 (IG) - Body ground |
SB - Body ground |
IG power supply |
Ignition switch ON |
11 to 14 V |
Ignition switch off |
Below 1 V |
W3-10 (B) - Body ground |
L - Body ground |
+B power supply |
Always |
11 to 14 V |
W3-8 (E) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
6. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
(a) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Check from the rear of the connector while it is connected to the air conditioning amplifier.
Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
J19-1 (IG+) - J19-14 (GND) |
B - W-B |
Ignition power supply |
Ignition switch ON |
11 to 14 V |
Ignition switch off |
Below 1 V |
J19-21 (B) - J19-14 (GND) |
GR - W-B |
Battery power source |
Always |
11 to 14 V |
J19-14 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
7. CHECK AIR CONDITIONING CONTROL ASSEMBLY
(a) Disconnect the J127 air conditioning control assembly connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
J127-4 (IG+) - J127-5 (GND) |
Y - W-B |
Ignition power supply |
Ignition switch ON |
11 to 14 V |
Ignition switch off |
Below 1 V |
J127-5 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
|