Lost Communication with "Door Control Module A" (U0199)
In this manual: Power Source, Network
~4min read
DESCRIPTION
DTC No.
DTC Detection Condition
Trouble Area
U0199
There is no communication from the outer mirror control ECU assembly LH.
Outer mirror control ECU assembly LH CAN branch wire or connector
Power source or inside of outer mirror control ECU assembly LH
Outer mirror control ECU assembly LH ground circuit
Outer mirror control ECU assembly LH
WIRING DIAGRAM
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
Some parts must be initialized and set when replacing or removing and installing parts.
Click here
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here
Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
RECONFIRM DTC OUTPUT
(a) Reconfirm DTCs.
HINT:
If DTC U1002 is output from Gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.
Result
Result
Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU).
A
DTC U1002 is output from main body ECU (multiplex network body ECU).
B
B
GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC
A
CHECK FOR OPEN IN CAN BUS WIRE (OUTER MIRROR CONTROL ECU ASSEMBLY LH CAN BRANCH WIRE)
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the outer mirror control ECU assembly LH connector.
*a
Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
N14-9 (CANP) - N14-8 (CANN)
Cable disconnected from negative (-) battery terminal
54 to 69 Ω
NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR
OK
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
N14-7 (GND) - Body ground
Cable disconnected from negative (-) battery terminal
Below 1 Ω
*a
Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)
(b) Reconnect the cable to the negative (-) battery terminal.
NOTICE:
When connecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Condition
Specified Condition
N14-6 (CPUB) - Body ground
Always
11 to 14 V
N14-14 (BDR) - Body ground
Always
11 to 14 V
N14-5 (SIG) - Body ground
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
OK
REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)