DESCRIPTION
There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
Symptom | Trouble Area |
| *1: w/ Pre-collision System *2: w/ Blind Spot Monitor System |
There is no resistance between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3. |
- Short to +B in CAN main bus line
- Short to +B in CAN branch line
- Central gateway ECU (network gateway ECU)
- Forward recognition camera*1
- Millimeter wave radar sensor assembly*1
- Blind spot monitor sensor RH*2
- No. 1 CAN junction terminal
- No. 1 CAN junction connector
- No. 2 CAN junction connector
- No. 7 CAN junction connector
|
WIRING DIAGRAM
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the No. 1 CAN junction connector. |
 |
*a |
Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b |
Front view of DLC3 |
*c |
to Millimeter Wave Radar Sensor (w/ Pre-collision System) |
*d |
to No. 7 CAN Junction Connector |
*e |
to No. 2 CAN Junction Connector |
|
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition | Connected to |
| *: w/ Pre-collision System |
A72-1 (CANH) - J17-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
Millimeter wave radar sensor* |
A72-3 (CANL) - J17-16 (BAT) |
A72-2 (CANH) - J17-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
No. 7 CAN junction connector |
A72-4 (CANL) - J17-16 (BAT) |
A72-6 (CANH) - J17-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
No. 2 CAN junction connector |
A72-7 (CANL) - J17-16 (BAT) |
Result | Proceed to |
OK |
A |
NG (No. 7 CAN junction connector CAN main wire) |
B |
NG (No. 2 CAN junction connector CAN main wire) |
C |
NG (Wire to ECU or sensor) |
D |
| A |
 |
REPLACE NO. 1 CAN JUNCTION CONNECTOR |
| C |
 |
GO TO STEP 4 |
| D |
 |
GO TO STEP 8 |
| B |
 |
|
CONNECT CONNECTOR
(a) Reconnect the A72 No. 1 CAN junction connector.
| NEXT |
 |
|
CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
(a) Disconnect the No. 7 CAN junction connector. |
 |
*a |
Front view of wire harness connector
(to No. 7 CAN Junction Connector) |
*b |
Front view of DLC3 |
*c |
to No. 1 CAN Junction Terminal |
*d |
to No. 1 CAN Junction Connector |
*e |
to Blind Spot Monitor Sensor RH (w/ Blind Spot Monitor System) |
|
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition | Connected to |
| *: w/ Blind Spot Monitor System |
R17-1 (CANH) - J17-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
No. 1 CAN junction terminal |
R17-4 (CANL) - J17-16 (BAT) |
R17-2 (CANH) - J17-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
No. 1 CAN junction connector |
R17-3 (CANL) - J17-16 (BAT) |
R17-5 (CANH) - J17-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
Blind spot monitor sensor RH* |
R17-8 (CANL) - J17-16 (BAT) |
Result | Proceed to |
OK |
A |
NG (No. 1 CAN junction connector CAN main wire) |
B |
NG (Wire to ECU or sensor) |
C |
| A |
 |
REPLACE NO. 7 CAN JUNCTION CONNECTOR |
| B |
 |
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR) |
| C |
 |
GO TO STEP 8 |
CONNECT CONNECTOR
(a) Reconnect the A72 No. 1 CAN junction connector.
| NEXT |
 |
|
CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
(a) Disconnect the No. 2 CAN junction connector. |
 |
*a |
Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b |
Front view of DLC3 |
*c |
to No. 1 CAN Junction Connector |
*d |
to Forward Recognition Camera (w/ Pre-collision System) |
*e |
to Central Gateway ECU (Network Gateway ECU) |
|
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition | Connected to |
| *: w/ Pre-collision System |
J187-1 (CANH) - J17-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
No. 1 CAN junction connector |
J187-12 (CANL) - J17-16 (BAT) |
J187-2 (CANH) - J17-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
Forward recognition camera* |
J187-13 (CANL) - J17-16 (BAT) |
J187-3 (CANH) - J17-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
Central gateway ECU (network gateway ECU) |
J187-14 (CANL) - J17-16 (BAT) |
Result | Proceed to |
OK |
A |
NG (No. 1 CAN junction connector CAN main wire) |
B |
NG (Central gateway ECU [network gateway ECU] CAN main wire) |
C |
NG (Wire to ECU or sensor) |
D |
| A |
 |
REPLACE NO. 2 CAN JUNCTION CONNECTOR |
| B |
 |
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR) |
| C |
 |
GO TO STEP 8 |
| D |
 |
|
CONNECT CONNECTOR
(a) Reconnect the J187 No. 2 CAN junction connector.
| NEXT |
 |
|
CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR)
(a) Disconnect the central gateway ECU (network gateway ECU) connector. |
 |
*a |
Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
*b |
Front view of DLC3 |
|
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
J169-23 (CA1H) - J17-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
J169-8 (CA1L) - J17-16 (BAT) |
| OK |
 |
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) |
| NG |
 |
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR) |
CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR)
(a) Reconnect all wire harness connectors. |
 |
*a |
Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
*b |
Front view of DLC3 |
|
|
(b) Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.
Click here 
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
J169-23 (CA1H) - J17-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
J169-8 (CA1L) - J17-16 (BAT) |
HINT:
- If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
- If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.
| OK |
 |
REPLACE ECU OR SENSOR |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|