Toyota Venza Quiz
Window / Glass

Inspection

In this manual: Window / Glass
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
12steps
~72min
3/5difficulty
Done 0 of 12
INSPECTION PROCEDURE

1. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

(a) Apply positive (+) battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

(b) Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

(c) Check that the motor gear rotates smoothly as follows:

OK:

Measurement Condition

Specified Condition
  1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
  2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).
  3. Disconnect and reconnect a negative (-) battery lead to terminal 10 (UP) within 1 second.

Motor gear rotates clockwise (Up)
  1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
  2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).
  3. Disconnect and reconnect a negative (-) battery lead to terminal 7 (DOWN) within 1 second.

Motor gear rotates counterclockwise (Down)
Text in Illustration

*1

Component without harness connected

(to Front Power Window Regulator Motor Assembly LH)
  • If the result is not as specified, replace the front power window regulator motor assembly LH.

CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

2. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

(a) Apply positive (+) battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

(b) Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

(c) Check that the motor gear rotates smoothly as follows:

OK:

Measurement Condition

Specified Condition
  1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
  2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).
  3. Disconnect and reconnect a negative (-) battery lead to terminal 10 (UP) within 1 second.

Motor gear rotates counterclockwise (Up)
  1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
  2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).
  3. Disconnect and reconnect a negative (-) battery lead to terminal 7 (DOWN) within 1 second.

Motor gear rotates clockwise (Down)
Text in Illustration

*1

Component without harness connected

(to Front Power Window Regulator Motor Assembly RH)
  • If the result is not as specified, replace the front power window regulator motor assembly RH.

CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.