Toyota Venza Quiz
1ar-fe Engine Mechanical

Installation

In this manual: 1ar-fe Engine Mechanical
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~2min read
5special tools
03060901201509872N·mlb·ft
Tightening torque found on this page
INSTALLATION PROCEDURE

1. INSTALL REAR ENGINE OIL SEAL

(a) Apply MP grease to the lip of a new oil seal.

NOTICE:

  • Do not allow foreign matter to contact the lip of the oil seal.
  • Do not allow MP grease to contact the dust seal.

(b) Using SST and a hammer, tap in the oil seal until its surface is flush with the edges of the cylinder block and crankcase.

SST: 09223-15030

SST: 09950-70010

09951-07150

NOTICE:

  • Keep the lip of the oil seal free from foreign matter.
  • Do not tap in the oil seal at an angle.

2. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

(a) Using SST, hold the crankshaft.

SST: 09213-54015

SST: 09330-00021

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-80650 (quantity: 2)

(b) Clean the bolts and their installation holes.

(c) Install the front drive plate spacer.

HINT:

Align the pin of the front drive plate spacer with the pin hole of the crankshaft.

(d) Install the drive plate and rear drive plate spacer to the crankshaft.

(e) Apply a few drops of adhesive to 2 or 3 threads of the bolt end.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

(f) Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

Torque:

98 N·m {999 kgf·cm, 72 ft·lbf}

NOTICE:

Do not strike or damage the drive plate installation bolts. Be sure to handle them carefully.

3. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for 2WD)

When Not Using the Engine Support Bridge: (See page )


When Using the Engine Support Bridge: (See page )


4. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for AWD)

When Not Using the Engine Support Bridge: (See page )


When Using the Engine Support Bridge: (See page )

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.