Volkswagen Golf Quiz
General information, paint

Adhesion promoter

In this manual: General information, paint
General body repairs, exterior — 230General body repairs, interior — 279General information, paint — 133Vechile- specific paint information — 27Heating, air conditioning — 156Auxiliary heater — 58Air conditioning system with refrigerant R134a — 1297- speed dual clutch gearbox 0CW — 544- cylinder injection engine(1.4 1 direct inction. turbocharger) — 182Fuel supply system - Petrol engines — 59Running gear, axles, steering — 221Brake system — 92Wheels and Tyres guide — 12Guide for using trailers — 11Wheels and Tyres Guide - General Information — 121Brake system (hybrid) — 73Electrical system — 326Communication — 65Electrical system, general information — 111
~2min read

Designation:

Adhesion promoter -LLS MAX 015- for plastics

Issued 10.2012

Product description

The adhesion promoter -LLS MAX 015- is a versatile single-pack product suitable for all plastic parts commonly found on vehicle exteriors.

Properties:

Easy to apply.

Good adhesion.

High elasticity

Technical data sheet

Substrate

Suitable substrates:

All plastic parts commonly found on vehicle exteriors (PP, EPDM, ABS, PC, PPO, PA, R-TPU, PBTP, PVC, PUR, PUR flexible foam, UP-GF).

Substrate pre-treatment:

The substrate must be free of release agents.

Before cleaning plastic parts, temper them for 60 minutes at +60 °C to “sweat out” the release agents.
  • Clean with anti-static plastic cleaner -LVM 001 001 A2- or with the milder slow-drying silicone remover -LVM 020 100 A5-.
Note The effort required for the necessary cleaning depends on the type and quantity of the release agent used. It is recommended to use an emery pad to help in cleaning. Let the thinner evaporate completely (e.g. air-dry overnight at ambient temperature or for 30-40 minutes at +60 °C).
Adhesion promoter
  • Before priming, clean lightly once more with anti-static plastic cleaner -LVM 001 001 A2- or slow-drying silicone remover -LVM 020 100 A5- (with anti-static effect).
Adhesion promoter

Application

Application:

  • Vigorously shake can for at least 2 minutes.
Adhesion promoter

Method of application: “spray”.

  • Apply one full coat (1-2 µm).

Spraying distance:

  • Maintain a distance of 20-25 cm.
Adhesion promoter

Flash-off time is 10-15 minutes at +20 °C ambient temperature.

Note If spray work must be interrupted, ensure that the nozzle is cleared to avoid clogging by inverting the can and spraying until the valve is empty. When treating small sand-through spots (max. 5.0 cm in diameter), the adhesion promoter -LLS MAX 015- can be recoated with top coat right away.

Finishing

Treat with:

Elastic 2-pack HS surfacer (for elasticisation, see relevant data sheet).

Recoat with:

2-pack HS top coat

Waterborne base coat and 2-pack HS clear coats

Caution Protective garments and equipment in accordance with work safety regulations must be worn. Observe safety information sheets as well as warnings on the label of the spray can.

Shake briefly before spraying each coat.

After fully emptying the spray can, dispose of as recycling material

Data
Adhesion promoter
VOC content: 2004/42/IIB(e)(840)730 The EU limit value for this product (product category IIB.e) in ready-to-spray form is max. 840 g/l of volatile organic compounds. The VOC content of this product in ready-to-spray form is max. 730 g/l.

Storage

The guaranteed shelf life is 60 months from date of production. May be used until the date stated on the label at latest if stored in sealed original containers at +20 °C.
Adhesion promoter

Storage conditions

The recommended storage temperature for this product is +20 °C to +25 °C.
Adhesion promoter

Test yourself

A quick Volkswagen Golf quiz: every answer comes with an explanation and a link to the manual page.