Volkswagen Polo Quiz
General Paint Information

Two-Part Fine Filling Paste, Flexible

In this manual: General Paint Information
General Paint Information — 128Towing Guide — 10Whels, Tires, Whel Alignment — 126Battery, Starter, Generator, Cruise Control — 65Windshield Wiper/ Washer System — 9Exterior Lights, Switches — 1Interior Lights, Switches — 7Wiring — 51Refrrigerant R134a Servicing — 134
~3min read

Definition:

Two-Part Fine Filling Paste, Flexible -LSP 787 100 A1-

Edition 07/2010

Product Description

The Two-Part Fine Filling Paste, Flexible -LSP 787 100 A1- is a two component filler paste with high filling characteristics. The product does not collapse and has excellent adhesion on a multiple base surfaces.

This filling paste is used especially for plastics:

Other Application Areas:

For repair of plastic exterior body components where surface is damaged with material removed (scratches, holes, rips), without being broken through For filling of KU-plastics, that were previously repaired with the Plastic Repair Set -D 007 700-.

For filling over a repair area to eliminate a mark

Application Instructions

Properties

Constant, fine, creamy consistency

High filling characteristics - no collapsing

Hardens quickly

Sands well

Good adhesion on metal and plastic

Base Surface

Suitable base surfaces:

Steel

Galvanized sheet steel

Aluminum

On all cleaned and sanded plastics in vehicle area

Fiberglass-reinforced plastics (UP-GF)

Well-sanded old paint or factory paint

Hardened two-part filler/two-part primers

Pre-treatment of base surfaces:

  • Remove any grease and sand the surface.
  • Bare metallic base surfaces are to be insulated with Two-Part Wash Primer -LHV 043 000 A2- and then filled with Two-Part HS Performance Filler. Sand the filler after drying.
  • With UP-GF underbodies, clean components of any residual agents and sand the surface.
Two-Part Fine Filling Paste, Flexible
  • Clean once more using the Silicone Remover, Long -LVM 020 100 A5- or Silicone Remover -LVM 020 000 A5- before reworking.
Two-Part Fine Filling Paste, Flexible

Reworking

Recommended structure:

Fine filling paste by itself.

Rework fine filling paste with Two-Part Fine Filling Paste -LSP 784 002 A2- or with Two-Part Spray Filling Paste -ALN 788 007- (except on galvanized steel). Prime bare spots and filled areas with Two-Part Wash Primer -LHV 043 000 A2- and then fill with Two-Part HS Performance Filler.
  • Then paint over with the top coat.
Note

Before filling, dry-sand the entire surface with P280-400 sandpaper.

Application Table
Two-Part Fine Filling Paste, Flexible
Mixing ratio 2 to 3 % by weight
Add hardener Two-Part Hardener -LVM 018 00 A1-
Pot life 2 to 4 minutes at +20 °C
Drying time (air drying at +20 °C room temperature) 20 to 30 minutes
Infrared drying:
short-wave approximately three minutes (at 50 % output)
middle-wave approximately five minutes
Sanding compatibility Preliminary sanding Final sanding
Wet as fine filling paste P180 grit as fine filling paste P320-P360 grit
Dry as filling paste P80 grit, as filling paste P120 grit as filling paste P120-P240 grit, as fine filling paste P280 grit
Caution This filling paste may not be applied to PVB (acid-hardening) adhesive primers or one-part primers (for example, synthetic resin). Application on thermoplastic or elastic coatings is also not possible. In these cases, only apply filler paste to bare steel.
Note

Before filling, dry-sand the entire surface with P280-320 sandpaper.

Avoid using excessive hardener paste, to prevent it from bleeding through, especially on daylight colors and light metallic colors.

Reaction temperature at least +5 °C.

Test yourself

A quick Volkswagen Polo quiz: every answer comes with an explanation and a link to the manual page.