Information about the brakes
and safety warnings first⇒
to the topic
New brake pads do not yet have full braking effectiveness during the first 200 to 300 km and must first bed in ⇒
. The slightly reduced braking force
can, however, be compensated by pressing the brake pedal harder. During the bedding-in period, the braking distance is longer in a full or emergency braking than with bedded-in brake pads. During the bedding-in period, avoid full braking and situations that place high loads on the brakes, for example following another vehicle too closely.
The wear of the brake pads depends greatly on operating conditions and driving style. In frequent city and short-distance driving, as well as sporty driving, have the thickness of the brake pads checked more often by a qualified workshop.
When driving with wet brakes, such as after driving through water, during heavy rain or after washing the vehicle, braking effectiveness may be delayed due to damp or, in winter, icy brake discs. The brakes must be dried by braking gently at higher speed as soon as possible. Make sure that no following vehicle or other road user is endangered in the process ⇒
.
A layer of salt on the brake discs and brake pads reduces braking efficiency and lengthens the braking distance. If you have not braked for a longer period on salt-treated roads, grind off the salt layer by braking carefully. ⇒
.
Corrosion on the brake discs and contamination of the brake pads are promoted by long periods of standing, low mileage and little use. If the brake pads are used little or not at all, or if corrosion is present, Volkswagen recommends cleaning the brake discs and brake pads by braking hard several times from a higher speed. Make sure that no following vehicle or other road user is endangered in the process. ⇒
.
Brake system malfunction
If you need to brake and the vehicle does not brake as usual (sudden increase in braking distance), a brake circuit may have failed. This is indicated by the warning lamp
lights up. Go to the nearest qualified workshop immediately to have the fault rectified. On the way there, drive at low speed and expect much longer braking distances and higher pedal pressure.
The brake booster only works when the engine is running and amplifies the pedal force that the driver applies to the brake pedal.
If the brake booster is not working or the vehicle is being towed, press the brake pedal harder, because the braking distance is longer without brake booster assistance. ⇒
.
New brake pads initially do not have optimum braking effectiveness.
- New brake pads do not reach their full braking efficiency until they have been run in for up to 300 km. During this time, reduced braking efficiency can be compensated for by applying more pressure to the brake pedal.
- To reduce the risk of accidents, serious injuries and loss of vehicle control, drive with particular care when you have new brake pads.
- During the running-in period of the new brake pads, never follow other vehicles too closely or create driving situations that place a heavy load on the brakes.
Overheated brakes reduce braking effectiveness and considerably increase the braking distance.
- When driving downhill, the brakes are subjected to particularly heavy loads and overheat very quickly.
- Before driving a long stretch with a steep downhill gradient, reduce your speed and shift to a lower gear or select a lower driving position. This uses the braking effect of the engine and relieves the load on the brakes.
- Front spoilers that are not standard equipment or are damaged can impair the air supply to the brakes and cause the brakes to overheat.
Wet brakes, or brakes that are icy or covered in salt, brake later and increase the braking distance.
- Test the brakes carefully.
- Always dry the brakes by applying them lightly several times and remove ice and salt, provided that visibility, weather, road and traffic conditions allow it.
Driving without the brake booster can considerably increase the braking distance and thereby cause accidents and serious injuries.
- Never switch off the engine or the ignition while the vehicle is moving.
- If the brake booster is not working or the vehicle is being towed, press the brake pedal harder, because the braking distance is longer without brake booster assistance.
- Never allow the brakes to drag by applying light pedal pressure when you do not actually need to brake. Continuous pressure on the brake pedal causes the brakes to overheat. This can considerably reduce braking performance, considerably lengthen the braking distance and, in some circumstances, lead to total brake failure.
- Before driving a long stretch with a steep downhill gradient, reduce your speed and shift to a lower gear or select a lower driving position. This uses the braking effect of the engine and relieves the load on the brakes. Otherwise the brakes could overheat and possibly fail. Only use the brakes when you need them to slow down or stop.
When checking the front brake pads,
also check the rear brake pads at the same time. The thickness of all brake pads must be checked regularly by visual inspection, looking at the brake pads through the openings in the wheels or from underneath the vehicle. If necessary, remove the wheels to carry out a thorough inspection. Always have the rear brakes checked by a qualified workshop. Volkswagen recommends the Volkswagen Partner for this.