Información general
Par de apriete de pernos estándar
En este manual: Información general
2pasos
~12min
2/5dificultad
Hecho 0 de 2
Descripción

Este vehículo tiene tanto pernos/tuercas de nuevo estándar basados en ISO* como pernos/tuercas de estándar anterior. Existen algunas diferencias entre estos dos tipos de pernos/tuercas: forma de la cabeza, grado de resistencia, ancho hexagonal entre caras y el par de apriete estándar.
Para orientarse, consulte la Tabla de pares de apriete (incluido el nuevo estándar).
Si el par de apriete no se indica en la descripción ni en la figura, consulte la Tabla de pares de apriete (incluido el nuevo estándar).
*ISO: Organización Internacional de Normalización
Tabla de pares de apriete (incluye nuevo estándar)ESTÁNDAR ANTERIOR
| Grado (grado de resistencia) | Tamaño del perno | Diámetro del perno mm | Ancho hexagonal entre caras mm | Paso mm | Par de apriete (sin lubricante) | |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Perno de cabeza hexagonal | Perno de brida hexagonal | |||||||||||
| N·m | kg-m | ft-lb | in-lb | N·m | kg-m | ft-lb | in-lb | |||||
| 4T | M6 | 6.0 | 10 | 1.0 | 5.5 | 0.56 | 4 | 49 | 7 | 0.71 | 5 | 62 |
| M8 | 8.0 | 12 | 1.25 | 13.5 | 1.4 | 10 | — | 17 | 1.7 | 13 | — | |
| 1.0 | 13.5 | 1.4 | 10 | — | 17 | 1.7 | 13 | — | ||||
| M10 | 10.0 | 14 | 1.5 | 28 | 2.9 | 21 | — | 35 | 3.6 | 26 | — | |
| 1.25 | 28 | 2.9 | 21 | — | 35 | 3.6 | 26 | — | ||||
| M12 | 12.0 | 17 | 1.75 | 45 | 4.6 | 33 | — | 55 | 5.6 | 41 | — | |
| 1.25 | 45 | 4.6 | 33 | — | 65 | 6.6 | 48 | — | ||||
| M14 | 14.0 | 19 | 1.5 | 80 | 8.2 | 59 | — | 100 | 10 | 74 | — | |
| 7T | M6 | 6.0 | 10 | 1.0 | 9 | 0.92 | 7 | 80 | 11 | 1.1 | 8 | 97 |
| M8 | 8.0 | 12 | 1.25 | 22 | 2.2 | 16 | — | 28 | 2.9 | 21 | — | |
| 1.0 | 22 | 2.2 | 16 | — | 28 | 2.9 | 21 | — | ||||
| M10 | 10.0 | 14 | 1.5 | 45 | 4.6 | 33 | — | 55 | 5.6 | 41 | — | |
| 1.25 | 45 | 4.6 | 33 | — | 55 | 5.6 | 41 | — | ||||
| M12 | 12.0 | 17 | 1.75 | 80 | 8.2 | 59 | — | 100 | 10 | 74 | — | |
| 1.25 | 80 | 8.2 | 59 | — | 100 | 10 | 74 | — | ||||
| M14 | 14.0 | 19 | 1.5 | 130 | 13 | 96 | — | 170 | 17 | 125 | — | |
| 9T | M6 | 6.0 | 10 | 1.0 | 11 | 1.1 | 8 | — | 13.5 | 1.4 | 10 | — |
| M8 | 8.0 | 12 | 1.25 | 28 | 2.9 | 21 | — | 35 | 3.6 | 26 | — | |
| 1.0 | 28 | 2.9 | 21 | — | 35 | 3.6 | 26 | — | ||||
| M10 | 10.0 | 14 | 1.5 | 55 | 5.6 | 41 | — | 80 | 8.2 | 59 | — | |
| 1.25 | 55 | 5.6 | 41 | — | 80 | 8.2 | 59 | — | ||||
| M12 | 12.0 | 17 | 1.75 | 100 | 10 | 74 | — | 130 | 13 | 96 | — | |
| 1.25 | 100 | 10 | 74 | — | 130 | 13 | 96 | — | ||||
| M14 | 14.0 | 19 | 1.5 | 170 | 17 | 125 | — | 210 | 21 | 155 | — | |
NUEVO ESTÁNDAR BASADO EN ISO
| Grado (grado de resistencia) | Tamaño del perno | Diámetro del perno mm | Ancho hexagonal entre caras mm | Paso mm | Par de apriete | |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Perno de cabeza hexagonal | Perno de brida hexagonal | |||||||||||
| N·m | kg-m | ft-lb | in-lb | N·m | kg-m | ft-lb | in-lb | |||||
4.8 (sin lubricante) |
M6 | 6.0 | 10 | 1.0 | 5.5 | 0.56 | 4 | 49 | 7 | 0.71 | 5 | 62 |
| M8 | 8.0 | 13 | 1.25 | 13.5 | 1.4 | 10 | — | 17 | 1.7 | 13 | — | |
| 1.0 | 13.5 | 1.4 | 10 | — | 17 | 1.7 | 13 | — | ||||
| M10 | 10.0 | 16 | 1.5 | 28 | 2.9 | 21 | — | 35 | 3.6 | 26 | — | |
| 1.25 | 28 | 2.9 | 21 | — | 35 | 3.6 | 26 | — | ||||
| M12 | 12.0 | 18 | 1.75 | 45 | 4.6 | 33 | — | 55 | 5.6 | 41 | — | |
| 1.25 | 45 | 4.6 | 33 | — | 65 | 6.6 | 48 | — | ||||
| M14 | 14.0 | 21 | 1.5 | 80 | 8.2 | 59 | — | 100 | 10 | 74 | — | |
4.8 (con lubricante) |
M6 | 6.0 | 10 | 1.0 | 4 | 0.41 | 3 | 35 | 5.5 | 0.56 | 4 | 49 |
| M8 | 8.0 | 13 | 1.25 | 11 | 1.1 | 8 | — | 13.5 | 1.4 | 10 | — | |
| 1.0 | 11 | 1.1 | 8 | — | 13.5 | 1.4 | 10 | — | ||||
| M10 | 10.0 | 16 | 1.5 | 22 | 2.2 | 16 | — | 28 | 2.9 | 21 | — | |
| 1.25 | 22 | 2.2 | 16 | — | 28 | 2.9 | 21 | — | ||||
| M12 | 12.0 | 18 | 1.75 | 35 | 3.6 | 26 | — | 45 | 4.6 | 33 | — | |
| 1.25 | 35 | 3.6 | 26 | — | 45 | 4.6 | 33 | — | ||||
| M14 | 14.0 | 21 | 1.5 | 65 | 6.6 | 48 | — | 80 | 8.2 | 59 | — | |
8.8 (con lubricante) |
M6 | 6.0 | 10 | 1.0 | 8 | 0.82 | 6 | 71 | 10 | 1.0 | 7 | 89 |
| M8 | 8.0 | 13 | 1.25 | 21 | 2.1 | 15 | — | 25 | 2.6 | 18 | — | |
| 1.0 | 21 | 2.1 | 15 | — | 25 | 2.6 | 18 | — | ||||
| M10 | 10.0 | 16 | 1.5 | 40 | 4.1 | 30 | — | 50 | 5.1 | 37 | — | |
| 1.25 | 40 | 4.1 | 30 | — | 50 | 5.1 | 37 | — | ||||
| M12 | 12.0 | 18 | 1.75 | 70 | 7.1 | 52 | — | 85 | 8.7 | 63 | — | |
| 1.25 | 70 | 7.1 | 52 | — | 85 | 8.7 | 63 | — | ||||
| M14 | 14.0 | 21 | 1.5 | 120 | 12 | 89 | — | 140 | 14 | 103 | — | |
10.9 (con lubricante) |
M6 | 6.0 | 10 | 1.0 | 10 | 1.0 | 7 | 89 | 12 | 1.2 | 9 | 106 |
| M8 | 8.0 | 13 | 1.25 | 27 | 2.8 | 20 | — | 32 | 3.3 | 24 | — | |
| 1.0 | 27 | 2.8 | 20 | — | 32 | 3.3 | 24 | — | ||||
| M10 | 10.0 | 16 | 1.5 | 55 | 5.6 | 41 | — | 65 | 6.6 | 48 | — | |
| 1.25 | 55 | 5.6 | 41 | — | 65 | 6.6 | 48 | — | ||||
| M12 | 12.0 | 18 | 1.75 | 95 | 9.7 | 70 | — | 110 | 11 | 81 | — | |
| 1.25 | 95 | 9.7 | 70 | — | 110 | 11 | 81 | — | ||||
| M14 | 14.0 | 21 | 1.5 | 160 | 16 | 118 | — | 180 | 18 | 133 | — | |
IDENTIFICACIÓN DE PERNOS Y TUERCAS

¿Le resultó útil esta página?