Chassis

Overview - Steering Gear

~6min read
03060901201508059N·mlb·ft
Tightening torque found on this page

Overview - Steering Gear, Steering Gear with Tie Rods

Overview - Steering Gear, Steering Gear with Tie Rods

1 - Electromechanical Steering Gear with Tie Rods

  • With Power Steering Control Module -J500-
  • Removing and installing. Refer to → Chapter "Steering Gear, Removing and Installing".
  • Servicing. Refer to → Chapter "Overview - Steering Gear".
  • There are different versions. Refer to the Parts Catalog.

A removable heat shield mat was installed on the steering gear at start of production. Be sure to install this mat if installing the old steering gear again.

A removable heat shield mat on the steering gear was replaced by a bonded heat shield mat as a running change. It is therefore not necessary to take the mat from the old steering gear and installing on a new steering gear.

A replacement steering gear comes with the bonded heat shield mat.

2 - Bolt

  • 80 N·m +180º turn
  • Always replace if removed

3 - Subframe

4 - Nut

  • Pushed into the subframe
  • Always replace if removed

5 - Steering Intermediate Shaft

6 - Bolt

  • Tightening specification -Item 1-

7 - Wheel Bearing Housing

8 - Nut

  • 100 N·m
  • Always replace if removed

Overview - Steering Gear

Note

  • Always replace self-locking nuts and bolts.
  • Welding or straighten work on any steering components is not permissible.
  • Use only Power Steering Gear Grease to lubricate the steering rack (on the pinion side) and the ball paths (on the engine side). Note: There are different types of grease for the left and right. For allocation. Refer to the Parts Catalog.
  • The clamps -1 and 8- are tensioned to different tightening specifications.
Overview - Steering Gear

1 - Clamp

  • Always replace if removed
  • Use the CV Joint Boot Clamp Tool to tension the clamp.

Note

It is not permitted to open the new clamp.

  • For the correct version. Refer to the Parts Catalog.

2 - Tie Rod

  • 100 N·m
  • Removing and installing. Refer to → Chapter "Tie Rod, Removing and Installing".
  • Grease the joint with Power Steering Gear Grease

3 - Electromechanical Steering Gear

  • Removing and installing. Refer to → Chapter "Steering Gear, Removing and Installing".
  • Grease the steering rack with Power Steering Gear Grease Note: There are different types of grease for the left and right. For allocation. Refer to the Parts Catalog.
  • There are different versions. Refer to the Parts Catalog.

A removable heat shield mat was installed on the steering gear at start of production. Be sure to install this mat if installing the old steering gear again.

A removable heat shield mat on the steering gear was replaced by a bonded heat shield mat as a running change. It is therefore not necessary to take the mat from the old steering gear and installing on a new steering gear.

A replacement steering gear comes with the bonded heat shield mat.

4 - Tie Rod End

  • Removing and installing. Refer to → Chapter "Tie Rod End, Removing and Installing".
  • Check dust caps for damage and correct seating
  • Check dimension. Refer to → Fig. "Tie Rod End Check Dimension"

5 - Nut

  • 80 N·m
  • Counterhold on the tie rod end when loosening or tightening

6 - Spring Clamp

  • Always replace if removed
  • Spring clamp, installing.

7 - Boot

  • Check for damage
  • Always replace if removed
  • Coat the inside of the joint boot seats all the way around and evenly with Power Steering Gear Grease before installing. Refer to the Parts Catalog.
  • Check the seat for the boot on the steering gear for damage before installing. If the steering gear housing is damaged, replace the steering gear.
  • Must not be twisted when toe is being adjusted
  • Make sure it is installed correctly.
  • Replacing. Refer to → Chapter "Boot, Removing and Installing".

8 - Clamp

  • Always replace if removed
  • Use the CV Joint Boot Clamp Tool to tension the clamp.

Note

It is not permitted to open the new clamp.

  • For the correct version. Refer to the Parts Catalog.

9 - Tie Rod

  • 100 N·m
  • Removing and installing. Refer to → Chapter "Tie Rod, Removing and Installing".
  • Grease the joint with Power Steering Gear Grease

10 - Tie Rod End

  • Removing and installing. Refer to → Chapter "Tie Rod End, Removing and Installing".
  • Check dust caps for damage and correct seating
  • Check dimension. Refer to → Fig. "Tie Rod End Check Dimension"

11 - Nut

  • 80 N·m
  • Counterhold on the tie rod end when loosening or tightening

12 - Spring Clamp

  • Always replace if removed
  • Spring clamp, installing.

13 - Boot

  • Check for damage
  • Always replace if removed
  • Coat the inside of the joint boot seats all the way around and evenly with Power Steering Gear Grease before installing. Refer to the Parts Catalog.
  • Check the seat for the boot on the steering gear for damage before installing. If the steering gear housing is damaged, replace the steering gear.
  • Must not be twisted when toe is being adjusted
  • Make sure it is installed correctly.
  • Replacing. Refer to → Chapter "Boot, Removing and Installing".

Tie Rod End Check Dimension

  • Place a steel ruler -2- on the tie rod end and push it all the way up to the edge -arrow- of the tie rod end -1-.
  • Replace the complete steering gear with the tie rod and tie rod end if the check dimension -a- is less than 188 mm.
A48-10702

Tensioning the Inner Clamp

- Mount the CV Joint Boot Clamp Tool-1- as illustrated. Make sure that the jaws of the clamp tool are seated in the corners -arrows- of the clamp.

- Tighten the clamp by turning the spindle using a torque wrench -2- (do not tilt the pliers).

  • Use torque wrench -2- with 5 to 50 N·m range (for example, Torque Wrench 1331 5-50Nm -VAG1331-).
  • Make sure the thread on the spindle -1- is easy to move. Lubricate with MoS2 grease, if necessary.
  • If the thread is tight, for example, dirty, the required tensioning force for the hose clamp will not be achieved in spite of correct torque specification settings.
A48-10734
Tensioning the Inner Clamp

Outer Boot Assembly

  • Dimension -a- 2 mm.
A48-10708