Hyundai Genesis DH Quiz
Body Electrical System

Power Door Lock Actuator Repair Procedures

In this manual: Body Electrical System
General Information — 9Engine Mechanical System — 103Engine Electrical System — 54Emission Control System — 23Engine Control System/Fuel System — 127Automatic Transmission System (SBC) — 90All-Wheel Drive (AWD) System — 20Drive Shaft and Axle — 27Suspension System — 41Steering — 19Restraints — 56Brake System — 56Body (Interior and Exterior) — 211Body Electrical System — 279Heating, Ventilation, and Air Conditioning — 55
21steps
~126min
4/5difficulty
Done 0 of 21

Inspection
  • Wrap the screwdriver or puller tool with protective tape.
  • Handle with care during storage and during disassembly/assembly, as it is easily contaminated by grease and oil.
  • Be careful not to scratch or break the trim panel and the upper part of the door trim, as well as the wood grain (real wood) garnish.
  • Be careful not to scratch the door trim and other parts.
Front Door Lock Module Inspection
  1. Remove the front door trim panel. (Refer to Body - "Front Door Trim")
  2. Remove the front door module. (Refer to Power Windows - "Power Window Switch")
  3. Disconnect the actuator connectors.
    PIN Code Terminal Information
    Front LH Door Front RH Door
    1 COM1 ADJUSTER
    2 Central Motor Lock/Unlock
    3 Door Lock COM2
    4 Key Unlock X
    5 COM2 X
    6 Lock/Unlock Central Motor
    7 ADJUSTER COM1
  4. After applying battery voltage to each terminal as shown below, check that the actuator operates correctly.
  5. Disconnect the power switch connector from the door lock actuator.
  6. Check the continuity between the terminals in the half-latched state according to the table.
  7. Perform the lock reset procedure when the power door latch (auto full lock) operation is malfunctioning. The lock reset procedure is as follows: "Remove the power door fuse > Install the power door fuse > TURN the ignition switch ON."
    Fuse Installation
    Driver Door Front Intelligent Junction Block (FSJB)
    Auxiliary Door
  8. Remove the rear door trim panel. (Refer to Body - "Rear Door Trim")
  9. Remove the rear door module. (Refer to Power Windows - "Power Window Switch")
  10. Disconnect the actuator connectors.
    PIN Code Terminal Information
    Rear LH Door Rear RH Door
    1 COM1 ADJUSTER
    2 Central Motor Lock/Unlock
    3 - COM2
    4 - -
    5 COM2 -
    6 Lock/Unlock Central Motor
    7 ADJUSTER COM1
  11. Check actuator operation by connecting power and ground as specified in the table. To prevent actuator damage, apply battery voltage only momentarily.
  12. Disconnect the power switch connector from the door lock actuator.
  13. Check the continuity between the terminals in the half-latched state according to the table.
  14. Perform the lock reset procedure when the power door latch (auto full lock) operation is malfunctioning. The lock reset procedure is as follows: "Remove the power door fuse > Install the power door fuse > TURN the ignition switch ON."
    Fuse Installation
    Rear RH Door Engine Room Fuse and Relay Box
    Rear LH Door
  15. Remove the luggage compartment trim. (Refer to Body - "Luggage Compartment Trim")
  16. Disconnect the 6P connector from the actuator.
  17. Check actuator operation by connecting power and ground as specified in the table. To prevent actuator damage, apply battery voltage only momentarily.
  18. Check the continuity between the terminals at each switch position according to the table.
  19. Check the continuity between the terminals and ground according to the table.
  20. Disconnect the connector (A) and the bolts from the hood switch.
  21. Check the continuity between the terminals and ground as specified in the table. (Refer to Body - "Hood Latch")
Inspection of Rear Door Lock Module / Trunk Lock Module Inspection / Trunk Open Switch / Hood Switch

Test yourself

A quick Hyundai Genesis DH quiz: every answer comes with an explanation and a link to the manual page.