Hyundai Kona Quiz
Restraints

Repair Procedures

In this manual: Restraints
General Information — 17Engine Mechanical System — 85Engine Electrical System — 50Emission Control System — 26Engine Control System/Fuel System — 152DCT (Dual Clutch Transmission) System — 50Four-Wheel Drive (4WD) System — 21Propeller Shaft and Axle (2WD-FF) — 28Suspension System (without ECS) — 32Steering — 21Restraints — 38Brake System — 64Body (Interior and Exterior) — 205Body Electrical System — 1Heating, Ventilation, and Air Conditioning — 66
29steps
~174min
4/5difficulty
0102030405011.89N·mlb·ft
Tightening torque found on this page
Done 0 of 29

Removal

Front Seat Belt Pretensioner (BPT)
  1. Disconnect the negative battery cable and wait at least three minutes before starting work.
  2. Remove the lower anchor bolt of the seat belt. (Refer to Body - "Front Seat Belt")
  3. Remove the door scuff plate. (Refer to Body - "Interior Trim")
  4. Remove the center pillar trim. (Refer to Body - "Interior Trim")
  5. Remove the seat belt (A) after loosening the upper anchor bolt.
  6. Disconnect the front seat belt pretensioner connector (A).
  7. Remove the seat belt pretensioner (A) after loosening the pretensioner mounting bolts.
  8. Disconnect the negative battery cable and wait at least three minutes before starting work.
  9. Remove the luggage compartment side trim. (Refer to Body - "Luggage Compartment Side Trim")
  10. Remove the rear pillar trim. (Refer to Body - "Rear Pillar Trim")
  11. Remove the rear seat belt lower anchor (A) by loosening the mounting bolts.
  12. Loosen the mounting bolts and remove the rear seat belt pretensioner (A).
Rear Seat Belt Pretensioner (BPT)

Installation

Front Seat Belt Pretensioner (BPT)
  1. Remove the ignition key from the vehicle.
  2. Disconnect the negative battery cable and wait at least three minutes.
  3. Install the seat belt pretensioner. Tightening torque: Bolt A: 7.8–11.8 N·m Bolt B: 39.2–54 N·m
  4. Connect the seat belt pretensioner connector.
  5. Install the front seat belt (A) by tightening the upper anchor bolt.

    Torque: 39.2 – 54 N·m

  6. Install the center pillar trim. (Refer to Body - "Interior Trim")
  7. Install the door scuff plate. (Refer to Body - "Interior Trim")
  8. Connect the negative battery cable.
  9. After installing the seat belt pretensioner, check the system operation:
    • Turn the ignition ON; the SRS indicator should illuminate for about six seconds and then go off.
  10. Remove the ignition key from the vehicle.
  11. Disconnect the negative battery cable and wait at least three minutes.
  12. Install the retractor (A).

    Torque: 39.2 – 54 N·m

  13. Install the rear seat belt lower anchor (A).

    Torque: 39.2 – 54 N·m

  14. Install the rear pillar trim. (Refer to Body - Rear Pillar Trim)
  15. Install the luggage compartment side trim. (Refer to Body - "Luggage Compartment Side Trim")
  16. Connect the negative battery cable.
  17. After installing the seat belt pretensioner, check the system operation:
    • Turn the ignition ON; the SRS indicator should illuminate for about six seconds and then go off.
Rear Seat Belt Pretensioner (BPT)

Test yourself

A quick Hyundai Kona quiz: every answer comes with an explanation and a link to the manual page.