Hyundai Palisade Quiz
Body (Interior and Exterior)

Crash Pad Garnish

In this manual: Body (Interior and Exterior)
General Information — 10Engine Mechanical System — 56Engine Electrical System — 28Emission Control System — 21Engine Control System/Fuel System — 42Automatic Transmission System (A8LF1) — 33All-Wheel Drive (AWD) System — 16Drive Shaft and Axle — 19Suspension System — 28Steering — 17Restraints — 20Brake System — 39Body (Interior and Exterior) — 142Body Electrical System — 171Heating, Ventilation, and Air Conditioning — 47Advanced Driver Assistance System (ADAS) — 44
11steps
~66min
3/5difficulty
Done 0 of 11

Components and Component Location

Component Location

Hyundai Palisade. Components and components location
1. Crash Pad Center Garnish
3. Crash Pad Garnish [LH]		 2. Crash Pad Garnish [RH]

Repair Procedures

Replacement

[Crash Pad Center Garnish]
Hyundai Palisade. Repair procedures
  • When removing with a flat-blade screwdriver or puller, wrap the tool with protective tape to prevent damage to the components.
  • Wear gloves to avoid cutting your hands.
Hyundai Palisade. Repair procedures
  • Use a plastic panel removal tool to remove the interior trim parts without damaging the surface.
  • Be careful not to bend or scratch the trim and panels.
  1. Remove the crash pad side cover [RH] (Refer to Crash Pad - "Crash Pad Side Cover").
  2. Loosen the mounting screws and remove the center garnish (A).
    Hyundai Palisade. Repair procedures
  3. Disconnect the start button connector (A).
    Hyundai Palisade. Repair procedures
  4. To install, reverse the removal procedure.
    Hyundai Palisade. Repair procedures
    • Replace any damaged clips (or pin-type retainers).
    • Make sure the connector is properly connected.
[Crash Pad Garnish LH]
Hyundai Palisade. Repair procedures
  • When removing with a flat-blade screwdriver or puller, wrap the tool with protective tape to prevent damage to the components.
  • Wear gloves to avoid cutting your hands.
Hyundai Palisade. Repair procedures
  • Use a plastic panel removal tool to remove the interior trim parts without damaging the surface.
  • Be careful not to bend or scratch the trim and panels.
  1. Remove the rear center panel (Refer to Crash Pad - "Center Panel").
  2. Using a flat-tip screwdriver, remove the decorative cover [LH] (A).
    Hyundai Palisade. Repair procedures
  3. To install, reverse the removal procedure.
    Hyundai Palisade. Repair procedures
    • Replace any damaged clips (or pin-type retainers).
[Crash Pad Garnish RH]
Hyundai Palisade. Repair procedures
  • When removing with a flat-blade screwdriver or puller, wrap the tool with protective tape to prevent damage to the components.
  • Wear gloves to avoid cutting your hands.
Hyundai Palisade. Repair procedures
  • Use a plastic panel removal tool to remove the interior trim parts without damaging the surface.
  • Be careful not to bend or scratch the trim and panels.
  1. Remove the rear center panel (Refer to Crash Pad - "Center Panel").
  2. Remove the crash pad center garnish (Refer to Crash Pad - "Crash Pad Garnish").
  3. Using a flat-tip screwdriver, remove the decorative cover [RH] (A).
    Hyundai Palisade. Repair procedures
  4. To install, reverse the removal procedure.
    Hyundai Palisade. Repair procedures
    • Replace any damaged clips (or pin-type retainers).

Test yourself

A quick Hyundai Palisade quiz: every answer comes with an explanation and a link to the manual page.