Suspension

Air Suspension Control Module

~7min read

Exploded View

Air suspension LH duct assembly Breather hose (exhaust) Breather hose (intake)
Air suspension control module Bracket Air connector
Air tube
Air suspension control module harness connector To rear RH air spring To rear LH air spring
To front RH shock absorber To air tank To front LH shock absorber
To breather hose (exhaust) To breather hose (intake)
:vehicle front
:Always replace after every disassembly.
:N·m (kg-m, ft-lb)
:N·m (kg-m, in-lb)

Removal and Installation

REMOVAL

Start engine.

Turn auto height mode control switch to ON, shift the shift position to N and set to normal height.

Turn OFF the electronic air suspension function. Refer to Operation.

Stop engine.

Lift up the vehicle.

Remove rear LH tire. Refer to ROAD WHEEL TIRE : Removal & Installation.

Remove rear LH wheel house protector. Refer to Removal and Installation.

Support the rear lower link with suitable jack (A) until most horizontal angle with vehicle on the ground.

Apply the matching marks to the air tube when replacing air connector .

Loosen the each air connector and perform air bleeding.

Remove breather hoses (exhaust) from air suspension LH duct assembly .

Remove breather hose (intake) from air suspension LH duct assembly .

Unhook the pawls to remove the breather hoses from the air suspension control module .

When reusing the air connector , remove air tubes and air connector together from air suspension control module .

When replacing the air connector, follow the procedure below.Fix part of the air connector, and remove part of the air connector.

Slide the air connector part to direction , and remove the part from the air tube .
Remove the air connector part from the air tube .

Remove harness clip and air tube clip form air suspension control module.

Remove bracket.

Disconnect air suspension control module harness connector , follow the procedure below.

Push the pawl . Move the lever in the direction until locked. Disconnect air suspension control module harness connector.

Remove air suspension control module from frame.

Remove bracket from air suspension control module if necessary.

INSTALLATION

Install bracket to air suspension control module if necessary.

Install air suspension control module to frame.

After installing the air suspension control module harness connector , move the lever in the direction to secure the locking.

Install bracket.

Install harness clip and air tube clip to air suspension control module.

When reusing the air connector , and install air tubes and air connectors together to air suspension control module .

When replaced the air connector, follow the procedure below.Install air connectors to air suspension control module. Insert the air tube straight into the air connector to the marked point which is applied when removing.

Install breather hoses to air suspension control module to secure the locking .

Install connecting the end of breather hose (intake) to air suspension LH duct assembly , insert it up to position .

Install breather hose (exhaust) to air suspension LH duct assembly , clip must be fixed between the matching marks of the breather hose (exhaust) made during removal.

Start engine.

If replacing air suspension control module, perform "ADDITIONAL SERVICE WHEN REPLACING AIR SUSPENSION CONTROL MODULE". Refer to Work Procedure.

Perform "Air filling/pressure measurement " using CONSULT. Refer to Work Support.

Use CONSULT and fill the air. Follow the procedure below.Fill the air to the air tank for 180 seconds. Refer to Work Support. Fill the inner pressure of shock absorber (With Built In Air Spring) to 5.7 bar. Refer to Work Support. Fill the inner pressure of air spring to 3.3 bar. Refer to Work Support.

Remove suitable jack from rear lower link.

Use CONSULT and fill the inner pressure of air spring to 3.3 bar. Refer to Work Support.

Stop engine.

Install rear LH wheel house protector. Refer to Removal and Installation.

Install rear LH tire. Refer to ROAD WHEEL TIRE : Removal & Installation.

Lift down the vehicle.

Start engine.

When replaced the air suspension control module, perform the height sensor calibration using CONSULT. Refer to Work Support.

Perform pressure measurements using CONSULT. Refer to Work Support.

Use CONSULT and vehicle to the normal height. Refer to Work Support.

Turn ON the electronic air suspension function. Refer to Operation.

Stop engine.

Perform inspection after installation. Refer to Inspection.

Perform adjustment after installation. Refer to Adjustment.

Inspection

INSPECTION AFTER INSTALLATION

  • Make sure the electronic air suspension function is turn ON. Refer to Operation.

  • Confirm that no warning message is displayed on the information display. Refer to Air suspension warning.

  • Perform the self-diagnosis using CONSULT. Check if any DTC is detected. Refer to CONSULT Function.

  • Confirm to close the hood.

  • Always check for the air leakage with soapy water.

Adjustment

ADJUSTMENT AFTER INSTALLATION

If replacing air suspension control module, perform "ADDITIONAL SERVICE WHEN REPLACING AIR SUSPENSION CONTROL MODULE." Refer to Work Procedure.